Filter
Top Products
2
A
Line out (see diagram ) Rear ground terminal
15 A fuse
Black
Blue with white stripe
Red
Yellow
*
2
To the metallic body or chassis of the car
Ignition switch
Fuse block
To an accessory terminal in the fuse block
To the remote lead of other equipment (200 mA max.)
Right speaker (rear)
Purple
Left speaker (rear)
Purple with black stripeGreen
Right speaker (front)
Green with black stripe
Left speaker (front)
Gray with black stripeWhiteWhite with black stripe
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
Antenna
terminal
Blue
To the automatic antenna if any (250 mA max.)
To external components (see diagram
)
Gray
Connecting the external amplifiers and/or subwoofer
B
Remote lead (blue with white stripe)
To the remote lead of other
equipment or automatic antenna
if any
Front speakers
Subwoofer
Rear speakers
Y-connector (not supplied for this unit)
JVC Amplifier
Front speakers
Connecting the external components
CD changer jack
When connecting two components in series
*
6
To disconnect the connector
Hold the connector tightly ( 1 ), then pull it out ( 2 ) .
C
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries.
Orange with white stripe
To car light control switch
Set “L/O Mode” to “Rear” (See page 25
of the INSTRUCTIONS.)
Set “L/O Mode” to “Woofer” (See page
25 of the INSTRUCTIONS.)
You can also connect a subwoofer to the
REAR LINE OUT terminals.
You can connect a power amplifier for
rear speakers.
A KS-BTA200
B *
6
CD-CH / KS-PD100 / KS-U57 / KS-U58
or
ELECTRICAL CONNECTIONS
Typical connections
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
1 Connect the colored leads of the power cord in the order specified in the illustration below.
2 Connect the antenna cord.
3 Finally connect the wiring harness to the unit.
You can connect amplifiers to upgrade your car
stereo system.
• Connect the remote lead (blue with white stripe)
to the remote lead of the other equipment so that it
can be controlled through this unit.
• Disconnect the speakers from this unit,
connect them to the amplifier. Leave the
speaker leads of this unit unused.
JVC AmplifierJVC Amplifier
When connecting the external components, refer also to the manuals supplied for the components and
adapters.
CAUTION:
Before connecting the external components, make sure that the unit is turned off.
You can connect the following JVC components to the CD changer jack.
JVC component Model name
CD changer (CD-CH) CH-X1500, etc.
You can also connect the following components through the various JVC adapters.
• Connection cords may need to be purchased separately.
Component Adapter Model name
Bluetooth device Bluetooth adapter KS-BTA200
iPod Interface adapter for iPod KS-PD100
Portable audio player with line
output jacks
Line input adapter KS-U57
Portable audio player with 3.5 mm
stereo mini jack
AUX input adapter KS-U58
When connecting more than one component (maximum: two), it is recommended that you connect the
components in series as explained on the left.
*
4
Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint
(if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.
*
5
Signal cord (not supplied for this unit)
*
6
To use these components, set the external input setting correctly (see page 25 of the INSTRUCTIONS).
*
1
Not supplied for this unit.
*
2
Before checking the operation of this unit prior to installation, this lead must be connected, otherwise the power
cannot be turned on.
*
3
Remote lead
Install_KD-G844[UI]f.indd 2Install_KD-G844[UI]f.indd 2 12/27/07 3:22:35 PM12/27/07 3:22:35 PM