Filter
Top Products
21-EN
About MobileHub™ Link
Connect a separately sold Junction Box and a
portable telephone (available from Nokia) to
control the incoming and outgoing calls of the
portable telephone.
Functions that can be operated from CVA-1004
CAUTION
• Even with hands-free operation, a driver can be
distracted during telephone operation or receiving a
call. For the sake of safety, drivers are requested to
refrain from operating the telephone while driving.
• For the sake of safety, operations other than incoming
calls and Speed-Dial outgoing calls cannot be used.
NOTES
• If a portable telephone is connected, its address book,
incoming and outgoing history and short message
history are downloaded to the Junction Box.
• Please refer to the instruction manual of the Junction
BOX.
Telephone Mode On and Off
1 Press BAND/TEL. for at least 2 seconds.
See relevant pages for each item.
NOTES
• When a portable telephone is not connected, “NO
PHONE” is displayed for at least 2 seconds, then the
mode returns to the original source mode.
• When the portable telephone is taken off the Junction
BOX during an incoming or outgoing call, or during a
hands-free call, the call will be treated as an ordinary
one by the portable telephone.
• When there is an incoming call while the power of
CVA-1004 is OFF, the power of CVA-1004 will turn
ON automatically for an ordinary call by the portable
telephone, but not for a hands-free call.
• Even if the power of the portable telephone is OFF,
when CVA-1004 is set to the telephone mode, the
power of the portable telephone will be turned ON.
• Even if the ACC power of the vehicle is turned OFF
(even if the engine is stopped) during a hands-free
call, the call is not disconnected, and an ordinary call
by the portable telephone is possible.
• If there is an incoming call during operation (except
an outgoing call or talking), operation mode will end
and switch to the incoming or talking mode.
• An outgoing call from a portable telephone is also
possible. However, you cannot perform different
operations at the same time from a portable telephone
and CVA-1004 as malfunction can result.
• With a Junction BOX connected, outgoing and
incoming history will also be recorded in the portable
telephone.
• While telephoning, the setting of CVA-1004
automatically turns to DEFEAT ON.
• When the call has finished, the unit returns to your
previous settings.
• The telephone volume can be adjusted from the CVA-
1004. The volume you set during the call is
memorized, and is automatically applied again on the
next call.
• If you press TITLE
in the display for selecting the
calling method, the Network Operator display will be
shown. Press TITLE
again to return to the
previous display.
• During a call, you can send dial tone signals 1 to 6
using preset buttons 1 through 6, and dial tone
signals 7 to 9, 0, and by pressing FUNC, and then
preset buttons 1 through 6.
Incoming Calls
1 Press -/J to receive an incoming call.
2 Press and hold BAND/TEL. for at least 2
seconds to finish a call.
The telephone mode will end and return to the
original source mode.
NOTES
• When the Automatic Calling mode is on, you can talk
after 3 seconds of receiving the incoming call.
• To switch between automatic calling and manual
calling, refer to "Setting the Call Receiving Method"
(page 23).
• Press and hold BAND/TEL. for at least 2 seconds
during an incoming call to disconnect it.
• You can call back by pressing :/J within 5 seconds
after finishing a call.
MobileHub™ Link Operation
(
Optional
)
Incoming Calls
Automatically
receive
Manually
receive
Missed call
announcement
(information icon)
Outgoing Calls
Call out
(Speed Dial)
Call out
(phone
book)
Call out (dialled)
Call out
(received)
Call out
(missed
call)
Short Messages
Display receiving
history
Display short
message
Mail arrival
announcement
(information icon)
BAND/TEL.
::
::
:/
JJ
JJ
J