Alpine IVA-W205R Car Video System User Manual


 
35-EN
01GB05IVAW205R.fm
ALPINE IVA-W205R 68-08564Z42-A (EN)
You can adjust the brightness of the button lighting at night with the
dimmer.
Setting item: LED DIMMER LEVEL
Setting level: -2 to +2
The adjustment is available when ON is set in “Setting the Brightness
of the Backlighting” (page 38).
System Setup Operation
1
Touch [SETUP] on the main source screen.
The SETUP selection screen is displayed.
2
Touch [SYSTEM].
The SYSTEM SETUP screen appears.
3
Touch [], [] or [OFF], [ON], etc., of the desired
item to change its setting.
Setting items:
IN INT. MUTE / IN INT. ICON / REMOTE SENSOR
*
4
/
CAMERA IN / NAV. IN / NAV. MIX
*
5
/ AUX IN / AUX IN LEVEL*
1
/
AUX IN SIGNAL
*
1
/ AUX OUT / BLUETOOTH IN /
USB ADAPTER / VISUAL KEY
*
2
/ OPTICAL OUT /
SUBWOOFER
*
3
*
1
Not displayed when OFF is set in “Setting the AUX Mode”
(page 36).
*
2
Not displayed when OFF is set in “Setting the Navigation
Mode” (page 36).
*
3
Not displayed when an external audio processor is connected.
*
4
When ON is set in “Setting the Picture Output” (page 36), the
item is displayed.
*
5
When ON is set in “Setting the Navigation Mode” (page 36),
the item is displayed.
4
Touch [RETURN] to return to the previous screen.
Touch and hold [RETURN] for at least 2 seconds to return to
the main source screen that was displayed before the setup
operation was started.
Immediately after changing the settings of System Mode (while the
system is writing data automatically) do not turn the ignition key
(engine key) to OFF. Otherwise, the settings may not be changed.
If an Alpine Ai-NET Interrupt Box (NVE-K200) is connected to the
IVA-W205R/IVA-W202R, an Auxiliary Source will be allowed to
interrupt the current audio source. For example, you can listen to the
voice guidance of your navigation system when it occurs even while
you are playing a CD or DVD. The CD/DVD player will be
automatically muted during voice guidance. For further details, please
refer to the manual for NVE-K200.
Setting item: IN INT. MUTE
Setting contents: OFF / ON
The auxiliary device being connected must have an Interrupt wire
with a negative trigger for this function to operate automatically.
Otherwise, a separate switch needs to be added to switch it manually.
The unit can display the icon of an external device, such as a telephone,
whenever a phone call comes in to tell you there is a phone call.
Setting item: IN INT. ICON
Setting contents: INT / TEL
For optional remote control operation, the remote sensor of the external
device (monitor, etc.) can be switched, as you prefer.
Setting items: REMOTE SENSOR
Setting contents: FRONT / REAR
If a touch panel rear monitor (connected to the Alpine rear monitor
output via the Monitor control lead) is touched, the command is
executed regardless of the remote control sensor switch setting. Note,
however, that the remote control sensor that has been set takes
priority if it has been 5 seconds since last touching the panel.
When an optional DVD changer or DVD player is connected, and the
remote control sensor is set to REAR, some soft button operations
( [] STOP, etc.) cannot be performed.
In this case, set the remote control sensor to FRONT.
Adjusting the Dimmer of Button Lighting at
Night
SYSTEM Setup
The Parking Brake must be engaged to access the SYSTEM
mode screen. Attempting to access this screen while driving
will display the warning-CAN’T OPERATE WHILE DRIVING.
The following steps 1 to 4 are common operations to each
“Setting item” of SYSTEM Setup. Refer to each section for
details.
Setting the External Device Interrupt Mode
OFF: The volume level can be adjusted in Interrupt mode.
ON: Sound will not be output. The icon that is set in “Setting
the Interrupt Icon Display” is displayed.
Setting the Interrupt Icon Display
INT: The INT icon appears on the display.
TEL: When the external device (telephone) sends the interrupt
signal, the telephone icon appears on the display.
Switching the function of the remote
sensor
FRONT: The remote sensor of this unit is effective.
REAR: The remote sensor of the external monitor
connected to AUX OUT of this unit becomes
effective. The remote control operates the
source connected to the AUX OUT terminals.
68-08564Z42-A_F.book Page 35 Wednesday, January 24, 2007 2:26 PM