Filter
Top Products
36 VRX6671z
7. To set a title of the stored USER pattern, op-
erate the JOYSTICK ¡ rightward or leftward
to select “TITLE” and press the ENT at the
center of the JOYSTICK ¡ to change into the
Title Input display.
∗For title inputting method, refer to the section
“Entering titles”.
8. Operate the JOYSTICK ¡ rightward or left-
ward to select “MENU” and press the ENT at
the center of the JOYSTICK ¡ to change into
the AUDIO-MODE display.
Professional mode/S.EQ opera-
tions
Note:
• The adjustment made in professional mode is not
reflected in the adjustment in easy mode. On the
contrary, the adjustment made in easy mode is not
reflected in the adjustment in professional mode.
S.EQ effect ON/OFF
∗ The factory default setting is “ON”.
1. Press the A-M button & to show the AUDIO-
MODE display.
2. Operate the JOYSTICK ¡ upward or down-
ward to select “S.EQ ON/OFF”. “ON” and
“OFF” items are displayed in the menu bar.
3.
Operate the JOYSTICK ¡ rightward or leftward
to select “ON” or “OFF” and press the ENT at
the center of the JOYSTICK ¡ to set it.
Note:
• If the S.EQ effect is set to OFF, the adjustment
made in “S.EQ operations” is not reflected in the
music source.
Calling S.EQ BASIC Pattern/USER
Pattern
1. Press the A-M button & to show the AUDIO-
MODE display.
2. Operate the JOYSTICK ¡ upward or down-
ward to select “S.EQ MODE”. “BASIC” and
“USER” items are displayed in the menu bar.
3. Operate the JOYSTICK ¡ rightward or left-
ward to select the item thus called, and press
the ENT at the center of the JOYSTICK ¡ to
show BASIC pattern selecting display or USER
pattern selection/memory display.
4. In the pattern selecting display, operate the
JOYSTICK ¡ rightward or leftward to select
P1 to P6, and press the ENT at the center of
the JOYSTICK ¡ to call corresponding S.EQ
pattern. In this display, pressing the No. but-
ton in correspondence to the PRESET buttons
# can also call the S.EQ pattern.
∗ After selecting P1 to P6 by operating the JOY-
STICK ¡ rightward or leftward, press the ENT
at the center of the JOYSTICK ¡ for 2 sec-
onds or longer to copy the selected pattern to
the USER pattern.
∗ Operate the JOYSTICK ¡ rightward or leftward
to select “EDIT”, and press the ENT at the cen-
ter of the JOYSTICK ¡ to show the S.EQ ad-
justing display, in which the properties of cur-
rently selected pattern can be adjusted.
∗ By pressing the BAND button % in BASIC pat-
tern selecting display or USER pattern selec-
tion/memory display you can switch between
the two patterns, BASIC and USER.
5. Operate the JOYSTICK ¡ rightward or leftward
to select “MENU”, and press the ENT at the cen-
ter of the JOYSTICK ¡ to return to the AUDIO-
MODE display.
Setting and storing S.EQ Properties/
Memory into USER Pattern
1. Repeat the steps 1 to 3 of the previous proce-
dure (Calling S.EQ BASIC Pattern/USER Pat-
tern) to show BASIC pattern selecting display
or USER pattern selection/memory display.
2. Operate the JOYSTICK ¡ upward or down-
ward to select “S.EQ EDIT”, and press the ENT
at the center of the JOYSTICK ¡ to show the
S.EQ adjusting display.
3. Select an item to be adjusted by operating the
JOYSTICK ¡ rightward or leftward in the
S.EQ adjusting display.
“DIFF” ➜ DIFFUSE
“C.WD” ➜ CAR WIDTH
“C.LG” ➜ CAR LENGTH
4. Operate the JOYSTICK ¡ upward or down-
ward to set each adjusting value.
∗
By pressing the
PRESET buttons #
once in the
S.EQ adjusting display, the setting value for cur-
rently stored USER pattern is obtained.
5.
After making adjustments to a desired pattern
by repeating the steps 3 and 4, operate the
JOYSTICK ¡ rightward or leftward to move the
cursor to “RTN”, and press the ENT at the cen-
ter of the JOYSTICK ¡ to change over to the
BASIC/USER pattern selection/memory display.
6.
Operate the JOYSTICK ¡ rightward or leftward
in the BASIC/USER pattern selection/memory
display to select USER memory P1 to P6 to be
stored, and press the ENT at the center of the
DSP operations