Filter
Top Products
Specifications
33
Specifications
Picture performance
LCD panel a-Si TFT Active Matrix
Pixel efficiency 99.99%
Viewing angle (up/down/left/right, contrast > 10:1)
89°/89°/89°/89° (typical)
Scan Normal 0%
Over scan 20%
Efficient picture size
698.4 × 392.9, 801.3 mm (w/h, dia)
(27
1
/2 × 15
1
/2, 31
5
/8 inches)
Resolution H 1920 dots, V 1080 lines
Aspect ratio 16:9
Input
Composite input (NTSC/PAL) connector
BNC type (1)
1 Vp-p ± 3 dB sync negative
Y/C input connector
4-pin mini-DIN (1)
Y: 1 Vp-p ± 3 dB sync negative
C: 0.286 Vp-p ± 3 dB (NTSC burst
signal level)
0.3 Vp-p ± 3 dB (PAL burst signal
level)
RGB/component input connectors
BNC type (3)
RGB input: 0.7 Vp-p ± 3 dB (Sync On
Green, 0.3 Vp-p sync negative)
Component input: 0.7 Vp-p ± 3 dB
(75% chrominance standard color
bar signal)
External synchronized input connector
BNC type (1)
0.3 to 4.0 V p-p ± bipolarity ternary or
negative polarity binary
HD15 input connector
D-sub 15-pin (1)
R/G/B: 0.7 Vp-p, sync positive (Sync
On Green, 0.3 Vp-p sync negative)
Sync: TTL level (polarity free, H/V
separate sync)
Plug & Play function: corresponds to
DDC2B
DVI input connector
DVI-D (1)
TMDS single link
Remote input connector
Parallel remote
Modular connector 8-pin (1)
Serial remote
D-sub 9-pin (RS-232C) (1)
RJ-45 modular connector
(ETHERNET) (1)
Optional input slot
2 slots
Signal format:
H: 15 to 45 kHz
V: 48 to 60 Hz
DC IN connector
DC5V/24V (output impedance 0.05
ohms or less)
Output
Composite output connector
BNC type (1)
Loop-through, with 75 ohms automatic
terminal function
Y/C output connector
4-pin mini-DIN (1)
Loop-through, with 75 ohms automatic
terminal function
RGB/component connectors
BNC type (3)
Loop-through, with 75 ohms automatic
terminal function
External synchronized output connector
BNC type (1)
Loop-through, with 75 ohms automatic
terminal function
General
Power LCD monitor (LMD-3250MD)
DC IN: 24 V 5.0 A 5 V 0.060 A
(Supplied from AC adaptor)
AC adaptor (Sony, AC-110MD)
AC IN: 100-240 V, 50/60Hz, 1.53 A to
0.58 A
DC OUT: 24 V 5.0 A 5 V 0.060 A
Power consumption
Maximum: approx. 136 W (when two
BKM-229X are installed)
Dimensions Approx. 783 × 479.2 × 124.3 mm
(including the projection parts)
(30
7
/8 × 18
7
/8 × 5 inches)
(w/h/d)
Mass LCD monitor (LMD-3250MD)
Approx. 13.3 kg (29 lb 5 oz) (when one
BKM-243HS is installed, pre-
installed)
Approx. 13.5 kg (29 lb 12 oz) (when
two BKM-229X are installed)
AC adaptor (AC-110MD)
Approx. 1.2 kg (2 lb 10 oz)
Operating conditions
Temperature
0 °C to 35 °C (32 °F to 95 °F)
Recommended temperature
20 °C to 30 °C (68 °F to 86 °F)
Humidity 30% to 85% (no condensation)
Pressure 700 hPa to 1060 hPa