Filter
Top Products
38-EN
01GB05VPAB222.fm
ALPINE VPA-B222 68-02065Z86-A (EN)
Adjusting the DVD Level
The volume (signal level) for Dolby Digital, Dolby PL II, DTS and
PCM modes can be set.
• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is canceled if the Decode mode is switched.
1
Check that Defeat mode is off (page 10).
2
Press and hold MUTE/RTN/SETUP for at least 2
seconds.
The SETUP screen is displayed.
3
Press the joystick up or down to select AP SETUP,
then press the joystick right.
The AP SETUP screen is displayed.
4
Press the joystick up or down to select DVD
LEVEL, then press the joystick right.
The DVD LEVEL screen is displayed.
5
Press the joystick up or down to select the desired
mode.
6
Press the joystick left or right to adjust level.
The level can be adjusted in the range of –5 to +5.
7
Repeat step 5 and 6 to set each level.
Storing Settings in the Memory
Adjustment or setting contents can be stored.
Contents that can be stored vary depends on the audio processor used.
1
Check that Defeat mode is off (page 10).
2
Press and hold MUTE/RTN/SETUP for at least 2
seconds.
The SETUP screen is displayed.
3
Press the joystick up or down to select AP SETUP,
then press the joystick right.
The AP SETUP screen is displayed.
4
Press the joystick up or down to select PRESET
MEMORY, then press the joystick right.
5
Press the joystick up or down to select any one of
the preset numbers (1 through 6), then press //
ENTER.
The setting contents are stored.
• The stored contents will not be deleted even when the battery power
cord is detached.
Calling up the Preset Memory
1
Check that Defeat mode is off (page 10).
2
Press and hold MUTE/RTN/SETUP for at least 2
seconds.
The SETUP screen is displayed.
3
Press the joystick up or down to select AP SETUP,
then press the joystick right.
The AP SETUP screen is displayed.
4
Press the joystick up or down to select PRESET
CALL, then press the joystick right.
5
Press the joystick up or down to select any one of
the preset numbers (1 through 6), then press //
ENTER.
• It takes a few moments to call up the preset memory.
Using the Pro Logic II Mode
Pro Logic processing can be conducted on the music signals recorded
on two channels to achieve Dolby Pro Logic II surround sound. For
two-channel Dolby Digital and DTS signals, there is also a “REAR
FILL” function for outputting the signals of the front channel to the rear
channel.
1
Check that Defeat mode is off (page 10).
2
Press and hold MUTE/RTN/SETUP for at least 2
seconds.
The SETUP screen is displayed.
3
Press the joystick up or down to select AP SETUP,
then press the joystick right.
The AP SETUP screen is displayed.
4
Press the joystick up or down to select D PLII/
REAR, then press the joystick right.
5
Press the joystick left or right to select the desired
mode of D PLII/REAR.
MOVIE: Suits the stereo TV shows and all programs encoded in
Dolby Surround. It improves the sound field directivity to
near that of discrete 5.1-channel sound.
MUSIC: Can be used for all stereo music recordings, and
provides a wide, deep sound field.
R.FILL: Depending on the input signals, the sound may only be
output from the front speakers. In this case, the “REAR
FILL” function can be used to output signals from the
rear speakers as well.
OFF: Turns D PLII/REAR FILL function to OFF.
01GB00VPAB222.book Page 38 Friday, January 20, 2006 6:37 PM