Filter
Top Products
53-EN
01GB07VPAB222.fm
ALPINE VPA-B222 68-02065Z86-A (EN)
Antenna Extension Cable
Right Front (+) Speaker Input Lead (Gray)
Right Front (–) Speaker Input Lead (Gray/Red)
Left Front (+) Speaker Input Lead (White)
Left Front (–) Speaker Input Lead (White/Red)
Remote Control Output Lead (White/Brown)
Connect this lead to the remote control input lead. This lead
outputs the controlling signals from the remote control.
Remote Control Output Lead (White/Brown)
Connect this lead to the remote control input lead. This lead
outputs the controlling signals from the remote control.
Illumination Lead (Orange)
This lead may be connected to the vehicle's instrument
cluster illumination lead. This will allow the backlighting of
the commander to dim whenever the vehicle's lights are
turned on.
Guide Control Lead (White/Green)
If an external audio processor is connected, connect this to
the guide control lead.
Commander (Included)
Power Supply Connector
Steering Remote Control Interface Connector
To steering remote control interface box.
Remote Control Eye Jack
Connect this to the remote control sensor unit.
Factory System Input Terminal
Navigation Input (RGB Input) Terminal
Connect this to the RGB output terminal of the Navigation
System.
Display Output (RGB Output) Terminal
Connect a 13P RGB terminal equipped monitor using the
RGB cable supplied with the unit.
Video Output Terminal
Connect this to the external front monitor using the RCA
extension cable supplied with the unit.
Subwoofer output Terminal
Connect the input lead of an amplifier for the subwoofer to
this terminal.
Rear output Terminal
Use when connecting an amplifier or equalizer.
Front output Terminal
Use when connecting an amplifier or equalizer.
Ai-NET Connector
Connect this to the output or input connector of other
product (CD changer, Equalizer, etc.) equipped with Ai-NET.
Guide Output Terminal
If an external audio processor is connected, outputs the
navigation interrupt voice signal that is input from the Alpine
navigation system, or the speaker input terminal.
Commander Terminal
iPod Direct Connector
Control iPod signals.
Connect this to an iPod, using the (also separately sold)
FULL SPEED™ Connection Cable (KCE-422i).
AV Select Connector
When this connector is connected to the optional expansion
box (VPE-S431), connect this to the HEAD UNIT terminal of
VPE-S431.
AUX Input Terminals
If these terminals are connected to the optional expansion
box (VPE-S431), the AUX input terminals are not used on
this unit. Connect AUX IN 1, 2 and 3, and the AUX OUT 1
and 2 terminals of the expansion box (VPE-S431) to the
external device(s).
Antenna Receptacle
Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
Audio Interrupt In Lead (Pink/Black)
Parking Brake Lead (Yellow/Blue)
Connect this lead to the power supply side of the parking
brake switch to transmit the parking brake status signals to
the VPA-B222.
Foot Brake Lead (Yellow/Black)
Connect to the vehicle's foot brake lead or brake lamp lead.
Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle’s fuse
box or another unused power source which provides (+)
12V only when the ignition is turned on or in the accessory
position.
Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle’s
battery.
Fuse Holder (10A)
Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
Right Front (+) Speaker Output Lead (Gray)
Right Front (–) Speaker Output Lead (Gray/Black)
Right Rear (–) Speaker Output Lead (Violet/Black)
Right Rear (+) Speaker Output Lead (Violet)
Left Rear (+) Speaker Output Lead (Green)
Left Rear (–) Speaker Output Lead (Green/Black)
Left Front (–) Speaker Output Lead (White/Black)
Left Front (+) Speaker Output Lead (White)
System Switch
When connecting an equalizer or divider using Ai-NET
feature, place this switch in the EQ/DIV position. When no
device is connected, leave the switch in the NORM position.
• Be sure to turn the power off on the unit before changing the
switch position.
ALPINE/OTHER switching button
Set to “ALPINE” for normal use.
Set to “OTHER” when connecting optional display interface
box.
01GB00VPAB222.book Page 53 Friday, January 20, 2006 6:37 PM