Filter
Top Products
15
Preparing the Remote Controller
Inserting the Batteries
1 Detach the battery cover.
2 Insert the two size AA/R6/UM3 batteries.
Be sure to match the + and – ends of the batteries with
the diagram inside the battery compartment.
3 Attach the battery cover.
Notes
• Do not mix new batteries with old batteries or different kinds of
batteries.
• To avoid corrosion, remove the batteries if the remote controller
is not to be used for a long time.
• Remove dead batteries immediately to avoid damage from
corrosion. If the remote controller does not operate smoothly,
replace both batteries at the same time.
• The life of the supplied batteries is about six months but this
varies depending on usage.
Pointing the remote controller in the
right direction
Point the remote controller toward the remote control
sensor.
Notes
• Place the unit away from strong light such as direct sunlight or
inverted fluorescent light which can prevent proper operation of
the remote controller.
• Using another remote controller of the same type in the same
room or using the unit near equipment which uses infrared rays
may cause operational interference.
• Do not put any object (such as a book) on the remote controller.
The buttons of the remote controller may be pressed by mistake
and drain the batteries.
• Make sure the audio rack doors do not have colored glass.
Placing the unit behind such doors may prevent proper remote
controller operation.
• If there is any obstacle between the remote controller and the
remote control sensor, the remote controller will not operate.
Switching the remote controller
function modes
Some buttons on the remote controller have two or more
functions. To set the functionality of these buttons, press one
of the four Mode (DVD, Recvr, Tape, TV) buttons in advance.
The function mode remains the same until another Mode
button is pressed.
(Details about the functions and the related function modes
are explained in each section.)
Press Mode Tape first before operating the z-connected
Integra/Onkyo cassette tape deck, MD recorder or CD
recorder (see pages 38, and 39).
Press Mode TV first before operating your TV.
To operate the TV with the supplied remote controller, you
need to let the remote controller learn the TV remote control
signals (see page 78).
30˚
30˚
About 5 m (16 feet)
Remote control sensor
12
3
The SEND/
LEARN indicator
is lit while any
button on the
remote controller
is pressed.
S
e
n
d
O
n
S
t
a
n
d
b
y
O
p
e
n
/
C
l
o
s
e
2
M
o
d
e
I
n
p
u
t
S
e
l
e
c
t
o
r
L
i
g
h
t
T
V
D
V
D
R
e
c
v
r
T
a
p
e
Mode buttons
Press Mode DVD first before operating the
built-in DVD player.
S
e
n
d
O
n
S
t
a
n
d
b
y
O
p
e
n
/
C
l
o
s
e
2
T
-
D Setup
IPM
SW Mode
Distance
T
-
D/
ST
A
-
B
Surround
A.Control
--
/
---
M
o
d
e
Enter
Repeat
Muting
Up/
Down
SP Setup Test Tone CH Sel
RC
-
507
M
Audio
Last M Program
Random
Late Night
Timer
Angle
Clear
Subtitle FM Mode
I
n
p
u
t
S
e
l
e
c
t
o
r
ENTER
L
i
g
h
t
T
V
D
i
s
p
l
a
y
VOL
C
H
T
V
I
n
p
u
t
S
e
t
u
p
D
V
D
R
e
c
v
r
T
a
p
e
Tun
Step
/
Slow
T
o
p
M
e
n
u
M
e
n
u
R
e
t
u
r
n
C
l
o
c
k
S
l
e
e
p
D
i
m
m
e
r
123
456
+
10
Search
0
789
M
o
d
e
T
V
D
V
D
R
e
c
v
r
T
a
p
e
Press Mode Recvr first before operating the speaker setting
and sound related operations.
M
o
d
e
T
V
D
V
D
R
e
c
v
r
T
a
p
e
M
o
d
e
T
V
D
V
D
R
e
c
v
r
T
a
p
e