Filter
Top Products
48
Enjoying the Sound Effects
See “The Input Sources and Available Listening Modes” on
page 47.
1
Theater-Dimensional indicator
Stereo/Theater-Dimensional
S
e
n
d
O
n
S
t
a
n
d
b
y
O
p
e
n
/
C
l
o
s
e
2
T
-
D Setup
IPM
SW Mode
Distance
T
-
D/
ST
A
-
B
Surround
A.Control
--
/
---
M
o
d
e
Enter
Repeat
Muting
Up/
Down
SP Setup Test Tone CH Sel
RC
-
507
M
Audio
Last M Program
Random
Late Night
Timer
Angle
Clear
Subtitle FM Mode
I
n
p
u
t
S
e
l
e
c
t
o
r
ENTER
L
i
g
h
t
T
V
D
i
s
p
l
a
y
VOL
C
H
T
V
I
n
p
u
t
S
e
t
u
p
D
V
D
R
e
c
v
r
T
a
p
e
Tun
Step
/
Slow
T
o
p
M
e
n
u
M
e
n
u
R
e
t
u
r
n
C
l
o
c
k
S
l
e
e
p
D
i
m
m
e
r
123
456
+
10
Search
0
789
Up/Down 5/∞
T-D/ST
T-D Setup
Choosing Theater-Dimensional Mode
The greater the distance
between the two speakers is,
the wider the angle is.
Listening angle
(“LSTN. ANGLE” appears in the display.)
Left speaker
The listening angle is the angle at the listening position
where the two lines from the left and right speakers meet.
You need to adjust the listening angle in the following
cases:
• Consider the listening angle as being formed from the
left and right
front speakers since the virtual surround
signals are output from the front speakers.
Set “LSTN. ANGLE” to one of the following settings, which
you feel is most effective (the listening angles in
parentheses are ideal):
• Normal (30°)
• Wide (40°)
• Narrow (20°)
Right speaker
40°
20°
L
R
L
R
Listening
angle
Theater-Dimensional mode is the technology which controls
the characteristics of the sounds reaching the listener’s left
and right ears, therefore, there is a sweet spot where you
can best experience the Theater-Dimensional effects. You
need to adjust the location of the sweet spot and these other
factors for the best possible Theater-Dimensional effect.
Notes
• Theater-Dimensional mode cannot be activated if;
– Headphones are connected, or
– The source is PCM sound with a sampling frequency higher than
48kHz.
• Theater-Dimensional mode will be canceled and the T-D indicator
goes off when:
– Another listening mode is chosen, or
– The input source is switched to a type of source which Theater-
Dimensional mode cannot process.
Before operating the
remote controller
Press Mode Recvr.
Press T-D/ST on the remote
controller or Stereo/Theater-
Dimensional on the unit.
“Theater-Dimensional” scrolls across in
the display and the Theater-Dimensional
indicator on the unit lights. In other
listening modes, press once to change to
Stereo and press again to change to T-D.
To change the listening angle, proceed to
the following steps.
Press T-D Setup.
“LSTN. ANGLE” is displayed, then the
current Listening Angle setting is
displayed.
Press Up/Down 5/∞ to select the
setting of the item.
Each press of the button changes the item
as follows:
NORMAL
↓
WIDE
↓
NARROW
Remote controller
Remote controller
only
Unit
2
3
Remote controller
only
Up/
Down
6
9
T
-
D/
ST
T
-
D Setup
8