Pioneer DEH-6400BT Car Stereo System User Manual


 
4 Press M.C. and hold untilthe customizing
illumination color setting appears in the dis-
play.
5 Press M.C. to select the primarycolor.
R (red)G (green)B (blue)
6 Turn M.C. to adjust the brightness level.
Adjustment range: 0 to 60
# You cannot selecta level below10 for all threeof
R (red),G (green), andB (blue) at thesame time.
# You can alsoperform the sameoperation on
other colors.
Notes
! You cannot create a custom illumination
color when SCAN or a set of colors (WARM,
AMBIENT,orCALM) is selected.
! You can create custom illumination colors
for both KEY COLOR and DISP COLOR.
Switching the dimmer setting
You can adjust the brightness of illumination.
% Press and hold
.
Using an AUX source
1 Insert the stereo mini pluginto the AUX
input jack.
2 Press SRC/OFF to select AUX asthe
source.
Note
AUX cannot be selected unless theauxiliary set-
ting is turned on. For more details, refer to AUX
(auxiliary input) on page 11.
Turning the clock display on
or off
% Press to turn the clock display on or
off.
# The clockdisplay disappears temporarilywhen
you perform otheroperations, but the clockdisplay
appears againafter 25seconds.
Connections
WARNING
! Use speakers over 50 W (output value)and
between 4 W to 8 W (impedance value).Do
not use 1 W to 3 W speakers forthis unit.
! The black cable is ground. When installing
this unit or power amp (sold separately),
make sure to connect the ground wirefirst.
Ensure that the ground wire is properly con-
nected to metal parts of the cars body. The
ground wire of the power amp and the oneof
this unit or any other device must becon-
nected to the car separately with different
screws. If the screw for the ground wire loos-
ens or falls out, it could result in fire, genera-
tion of smoke or malfunction.
Ground wire
Metal parts of car’s bod
y
POWER AMP
Other devices
(Another electronic
device in the car)
Important
! When installing this unit in a vehicle without
an ACC (accessory) position on the ignition
switch, failure to connect the red cableto the
terminal that detectsoperation of the ignition
key may result in battery drain.
O
N
S
T
A
R
T
O
F
F
ACC position NoACC position
! Use this unit with a 12-volt battery and nega-
tive grounding only. Failureto do so may re-
sult in a fire or malfunction.
! To prevent a short-circuit, overheatingor mal-
function, be sure to follow thedirections
below.
Disconnect thenegative terminal ofthe bat-
tery before installation.
Secure thewiring with cableclamps or adhe-
sive tape.Wrap adhesivetape around wiring
that comesinto contact withmetal parts to
protect thewiring.
Placeall cables away frommoving parts,
such asthe shift lever andseat rails.
Placeall cables away fromhot places, such
as nearthe heater outlet.
Donot connect theyellow cable tothe battery
by passingit through thehole to the engine
compartment.
Coverany disconnected cable connectors
with insulatingtape.
Do notshorten any cables.
Nevercut the insulation ofthe power cableof
this unitin order to sharethe power with
other devices.The current capacityof the
cable islimited.
Usea fuse of therating prescribed.
Never wirethe negative speakercable directly
to ground.
Neverband together negative cablesof multi-
ple speakers.
! When this unit is on, control signalsare sent
through the blue/white cable. Connect this
cable to the system remote control of anex-
ternal power amp or the vehicles auto-anten-
na relay control terminal (max. 300mA
12VDC). If the vehicle is equipped with a
glass antenna, connect it to the antenna
booster power supply terminal.
! Never connect the blue/white cable tothe
power terminal of an external power amp.
Also, never connect it to thepower terminal
of the auto antenna. Doing so may result in
battery drain or a malfunction.
English
Operating this unit
13
Section
Installation
En
02
03