5900335 © 2005 JCM-American Corporation
A-2
Appendix A Optipay™ CC TROUBLE SHOOTING
Diagnosis Using a Palm Pilot
®
Set-
ting Module
If a Coin Changer fault occurs, the Palm Pilot
®
Set-
ting Module displays the appropriate status or error
message as soon as you connect it to the RJ-45
interface jack on the Coin Changer’s front panel
(see chapter 11 "Configuration"). Depending on
the operating mode or fault, three status or fault
messages are displayed as follows:
•
INFO messages: used in general only for
information about particular operating states
•
AN/AB messages: indicate where a coin was
accepted (AN) or why a coin was rejected
(AB)
•
FE messages: indicate why the Coin Changer
no longer functions (Table A-2).
Yellow
Flashes
Twice
Coins stuck in
vend area or
motor failure
Remove tube cassette
and any jammed coins,
then vend one coin from
each tube using the
inventory keys or Ser-
vice case
Yellow
Flashes
3 times
Coin changer
inhibited
by Vending
Machine
Check Vending
Machine (possibly
empty or defective)
Red
Flashes
once
Fault in Coin
Validator
Remove jammed coins
by pressing the return
lever on the Coin Valida-
tor or Service case, Coin
Validator may have to be
exchanged
Red
Flashes
twice
Fault in Coin
Validator
Service case, Coin
Validator may have to be
exchanged
Red
Flashes
3 times
Vending
Machine no
longer com-
municates
with Coin
Changer (has
sent no com-
mand in 2
secs.)
Check Vending
Machine control or
connecting cable
Table A-2 Display Indicators
Display Meaning Trouble
INFO
INFO -01
Return Lever
pressed or a
switch in Coin
Validator defec-
tive
No error or, check the
return mechanism in
Vending Machine, or
Service case
Table A-1 LED Indicator Meanings (Continued)
LED Meaning Trouble
InFo-09 String sensor
active
Coin on string
recognized (no error),
or
check sensor
(Service case)
InFo-09A Tube coins are
delivered to the
cash-box after
a recognized
string manipu-
lation
No error.
This function can be
deactivated however,
using PRO 04 02
InFo-80 Coin Changer
inhibited by
Vending
Machine
Check Vending
Machine (possibly
empty or defective)
AN
An X YY
An X YY
Accepted coin
will be sorted
into:
X = 0 cash-box
X = 1 left tube
X = 2 middle
left tube
X = 3 middle
right tube
X = 4 right tube
Inserted coins
accepted in the
coin channel
YY = 01–16
(Channel No.)
No error
AB
Ab-01 Measured
inserted coin
values are out-
side the accep-
tance band limit
If necessary, widen
acceptance band limit
using with WinEMP
©
or
PalmEMP
©
Ab-02 Inserted coin
inhibited by the
Coin Changer
Enable coin channel
using DIP Switch Block
or Palm Setting Module
with WinEMP
©
or Palm
Pilot
®
with PalmA66
©
Ab-03 Inserted coin
has not passed
through mea-
surement sec-
tion in the
appropriate
amount of time
Remove coins or for-
eign objects by press-
ing the return lever on
the Coin Validator, or
check measurement by
air-core coil or CP2
level (Service case)
Ab-04 Inserted coin
was not recog-
nized
Insert coin again more
slowly
Ab-05 CP3 or CP4
sensor active
Insert coin more slowly,
or inserted coin not on
string or check sensors
(Service case)
Table A-2 Display Indicators (Continued)
Display Meaning Trouble
