Filter
Top Products
65
49
E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
64
48
E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
MENU:
Audio Settings (for VD7700U)
(continued)
: Previous menu
: Exit
SP SETUP
(continued)
(Surround speaker setting)
SURROUND
:
for large speakers, when bass
playback is possible (at least
100 Hz or lower)
:
for small speakers, or when
bass playback is not possible
:
when not using surround
speakers
default: LARGE
NONE
SMALL
LARGE
a or
or
[}] or [{] a []] or [[]
a [ENTER]
Remote
LARGE
SMALLNONE
SURROUND
Panel
(Subwoofer speaker setting)
A subwoofer (option, CJ-SW38 recom-
mended) is required. A power amplifier
(option) is also required for connecting
a subwoofer.
SUB • W
:
when using a subwoofer
:
when not using a subwoofer
default: NO
NO
YES
a or
[}] or [{] a []] or [[]
a [ENTER]
Remote
YESNO
SUB • W
Panel
SP LEVEL
(Speaker Level)
(Adjusting the output balance of each
speaker)
(Left front speaker output balance)
(Center speaker output balance)
(Right front speaker output balance)
(Right surround speaker output bal-
ance)
(Left surround speaker output balance)
(Subwoofer speaker output balance)
SUB
¡
W
L
¡
SURROUND
R
¡
SURROUND
FRONT R
CENTER
FRONT L
Setting range: –12 dB to +12 dB
(1 dB steps)
Default: ± 0 dB for all speakers
A test signal (a continuous tone) is
output from each speaker for
approximately two seconds.
Adjust the output balance so that
the tone appears to have the same
volume from each speaker.
Adjusting the output balance:
Adjust the volume of all of the other
speakers to the volume level of the
speaker from which the test signal
appears to be the quietest.
¡If the speaker setting is “NONE” or
“NO” for a speaker, the test signal
is not output and that speaker
cannot be selected. (a page 63)
¡Turn [VOLUME] or press [}] or
[{] (VOLUME) to adjust the vol-
ume of the test signal.
q Touch the image of the speaker you
want to set.
w : UP
: Down
q [}] or [{]
w [[] : UP
[]] : Down
Remote
]
[
Panel
Menu Setting Value Operations
Touch to select
: Previous menu
: Exit
SP DELAY
(Speaker Delay)
(Adjusting the timing with which the
audio from each speaker reaches the
listener’s position)
(Center speaker delay time setting)
(Surround speaker delay time setting)
¡Make this adjustment while listening
to sound.
¡
If the speaker setting is “NONE” for a
speaker, that speaker cannot be
selected.
(a page 63)
SURROUND
CENTER
Setting range:
Center speaker...
0 ms to 5 ms (1 ms steps)
Surround speakers...
0 ms to 15 ms (1 ms steps)
1 ms = 0.001 seconds
Default: 0 ms for all speakers
q Touch a speaker image. (Center or
Surround)
w : Long
: Short
q [}] or [{]
w [[] : Long
[]] : Short
Remote
]
[
Panel
VTR LEVEL
(Setting the VTR (VTR1/VTR2) input
Level)
Make this setting if it is not possible to
adjust the volume through the con-
nected device (on the output side).
Note: This setting is adjustable for an
external device that is connected to
VTR1 or VTR2. (e.g. VCR)
: Input level
default: ±0 dB
Notes:
¡If the input level from
VTR1/VTR2 is too high, the
audio will not be output nor-
mally. Adjust the input level
so that “OVER” does not
appear.
¡After setting the input level
The volume can be adjusted
by turning the volume knob or
pressing [}] or [{] (VOL-
UME) on the remote control.
+6
dB
+4 dB+2 dB
±
0 dB
–2 dB–4 dB–6 dB
: Lower
: Higher
[]] : Lower
[[] : Higher
Remote
[
]
Panel
Menu Setting Value Operations
Lower Higher