Filter
Top Products
Common
Operations
Adjusting
the non-fade volume
* The factory default setting
is
"NFVOL
+6".
(Adjustment range:
-6
to
+6)
1.
Press the [MENU] button to switch to the
menu mode.
2.
Press the
[!]
or
[T]
button to select "NFVOL".
3.
Turn the [VOLUME] knob to adjust the
nonfader volume.
4.
Press the [MENU] button to return to the
previous mode.
Verifying
your
SIRIUS ID (Sirius
mode
only)
1.
Press the [MENU] button to switch to the
menu mode.
2.
Press the
[!]
or
[T]
button to select "SID
DISP".
3.
Press the [ENT] button.
The source unit displays the high-order 6
digits of the SIRIUS
10
in
the Operation status
information.
4.
Turn the [VOLUME] knob clockwise to change
the low-order 6 digits of the SIRIUS
10.
To display the high-order 6 digits of the
SIRIUS
10
again, turn the [VOLUME] knob
counterclockwise.
5.
Press the [ENT] button.
6.
Press the [MENU] button to return to the
previous mode.
Switching
TVNTR
mode
(TV
mode
only)
This function switches TV to VTR.
1.
Press the [MENU] button to switch to the
menu mode.
2.
Press the
[!]
or
[T]
button to select "TVNTR".
3.
Press and hold the [ENT] button to select TV
or VTR.
Setting
the TV area (TV
mode
only)
The TV tuner area setting changes by the TV
area you selected.
1.
Press the [MENU] button to switch to the
menu mode.
2.
Press the
[!]
or [T] button
to
select "TV AREA".
3.
Turn the [VOLUME] knob to select the
reception area.
4.
Press the [MENU] button to return to the
previous mode.
The above operations are required when a TV
tuner other than TTX7501 z is connected.
Setting
the TV
diver
(TV
mode
only)
You can change the reception setting for the TV
antenna connected
to
the TV tuner.
1.
Press the.[MENU] button to switch to the
menu mode.
2.
Press the
[!]
or
[T]
button to select "TV
DIVER".
3.
Turn the [VOLUME] knob to set the setting to
"ON" or "OFF".
eON:
Sets reception emphasizing the visual.
eOFF:
Sets the diver setting to OFF.
4.
Press the [MENU] button to return to the
previous mode.
Selecting
AUX
IN
sensitivity
(AUX
mode
only)
Make the following settings to select the
sensitivity when sounds from external devices
connected to this unit are difficult to hear even
after adjusting the volume.
* The factory default setting
is
"MID".
1.
Press the [MENU] button
to
switch to the
menu mode.
2.
Press the
[!]
or
[T]
button to select "AUX
SENS".
3.
Turn the [VOLUME] knob to select from
"HIGH", "MID" or "LOW".
4.
Press the [MENU] button to return to the
previous mode.
Note:
• For telephone interrupt,
AUX
SENS is always
"MID".
Adjusting
the
display
contrast
You can adjust the display contrast to match the
angle of installation of the unit.
* The factory default setting
is
"4". (Adjustment
level:
1
to
8)
1.
Press the [MENU] button to switch to the
menu mode.
2.
Press the
[!]
or
[T]
button to select
"CONTRAST".
3.
Turn the [VOLUME] knob to adjust the
contrast.
4.
Press the [MENU] button to return to the
previous mode.
22
CMD5