Denon ADV-1000 Car Video System User Manual


  Open as PDF
of 95
 
10
ENGLISH
9
REMOTE CONTROL UNIT
• The included remote control unit (RC-901) can be used to operate not only this unit but other remote control compatible
DENON components as well. In addition, the memory contains the control signals for other remote control units, so it can be
used to operate non-Denon remote control compatible products.
(1) Inserting the batteries
q Remove the remote control unit’s rear cover.
w Set three R6P/AA batteries in the battery compartment in
the indicated direction.
e Put the rear cover back on.
Notes on Batteries
• Use R6P/AA batteries in the remote control unit.
• The batteries should be replaced with new ones
approximately once a year, though this depends on the
frequency of usage.
• Even if less than a year has passed, replace the batteries
with new ones if the set does not operate even when the
remote control unit is operated nearby the set. (The included
battery is only for verifying operation. Replace it with a new
battery as soon as possible.)
• When inserting the batteries, be sure to do so in the proper
direction, following the “≈” and “√” marks in the battery
compartment.
• To prevent damage or leakage of battery fluid:
• Do not use a new battery together with an old one.
• Do not use two different types of batteries.
• Do not short-circuit, disassemble, heat or dispose of
batteries in flames.
• Remove the batteries from the remote control unit when
you do not plan to use it for an extended period of time.
• If the battery fluid should leak, carefully wipe the fluid off the
inside of the battery compartment and insert new batteries.
• When replacing the batteries, have the new batteries ready
and insert them as quickly as possible.
(2) Using the remote control unit
C
8
1
:
0
2
:
4
6
D
V
D
A
U
T
O
D
I
G
D
I
G
I
T
A
L
V
O
L
U
M
E
B
A
N
D
M
O
D
E
M
E
N
U
F
U
N
C
T
I
O
N
D
I
S
P
L
A
Y
R
E
T
U
R
N
I
N
P
U
T
M
O
D
E
S
U
R
R
O
U
N
D
T
O
P
M
E
N
U
S
E
T
U
P
S
D
B
/
T
O
N
E
MUTE
S
U
R
R
.
P
A
R
A
S
U
B
T
I
T
L
E
A
N
G
L
E
A
U
D
I
O
S
H
I
F
T
C
H
.
S
E
L
E
C
T
C
H
T
.
T
O
N
E
T
U
P
R
O
G
/
D
I
R
E
C
T
R
E
P
E
A
T
A
-
B
R
E
P
E
A
T
R
A
N
D
O
M
D
V
D
T
V
/
V
C
R
C
H
V
O
L
S
L
E
E
P
ON
OF
F
R
E
M
O
C
O
N
M
O
D
E
2
3
4
5
6
8
9
0
7
1
S
T
A
T
U
S
C
D
R
/
M
D
/
T
A
P
E
T
U
N
E
R
/
T
V
/
V
C
R
V
C
R
P
O
W
E
R
T
V
P
O
W
E
R
T
V
V
C
R
N
T
S
C
/
P
A
L
E
N
T
E
R
MUTE
O
N
2
3
4
5
6
C
L
E
A
R
C
ALL
0
M
E
M
O
P
O
W
E
R
C
H
C
H
C
H
OFF
1
8
9
+
1
0
7
30°
30°
Approx. 7m
• Point the remote control unit at the remote sensor on the
main unit as shown on the diagram.
• The remote control unit can be used from a straight distance
of approximately 7 meters from the main unit, but this
distance will be shorter if there are obstacles in the way or
if the remote control unit is not pointed directly at the
remote sensor.
• The remote control unit can be operated at a horizontal angle
of up to 30 degrees with respect to the remote sensor.
NOTES:
• It may be difficult to operate the remote control unit if the
remote sensor is exposed to direct sunlight or strong
artificial light.
• Do not press buttons on the main unit and remote control
unit simultaneously. Doing so may result in malfunction.
• Neon signs or other devices emitting pulse-type noise
nearby may result in malfunction, so keep the set as far
away from such devices as possible.
(3) Preset memory
[1] Audio Component
• The signals of your other Denon products can be stored in the
included remote control unit’s preset memory to operate
either the CDR, MD or TAPE function.
Operation is not possible for some models.
[2] TV
• Other makes of components can be operated by setting the
preset memory for your make of TV.
This remote control unit can be used to operate components
of other manufacturers without using the learning function by
registering the manufacturer of the components as shown on
the List of Preset Codes (attached sheet).
Operation is not possible for some models.
VOLUME
ENTER
BAND
MODE
MENU
FUNCTION
DISPLAY RETURN INPUT MODESURROUND
TOP MENU
SETUP
SDB/TONE
MUTE
SURR.PARA
SUB TITLE ANGLE
AUDIO
RTRDS CT
PTY
SHIFT
CH.SELECT
CH
T.TONE
TU
PROG/DIRECT
REPEAT A-B
REPEAT RANDOM
DVD
TV/VCR
CH
VOL
SLEEP
ON
OFF
REMOCON MODE
2
3
4
56
8
9
CLEAR
CALL
0
+10
7
1
STATUS
CDR/MD/TAPE
TUNER/TV/VCR
VCR POWERVCR POWER
TV POWERTV POWER
TV
VCR
NTSC/PAL
MEMO
POWERPOWER
CH
CH
CH
1
1
VOLUME
ENTER
BAND
MODE
MENU
FUNCTION
DISPLAY RETURN INPUT MODESURROUND
TOP MENU
SETUP
SDB/TONE
MUTE
SURR.PARA
SUB TITLE ANGLE
AUDIO
RTRDS CT
PTY
SHIFT
CH.SELECT
CH
T.TONE
TU
PROG/DIRECT
REPEAT A-B
REPEAT RANDOM
DVD
TV/VCR
CH
VOL
SLEEP
ON
OFF
REMOCON MODE
2
3
4
56
8
9
CLEAR
CALL
0
+10
7
1
STATUS
CDR/MD/TAPE
TUNER/TV/VCR
VCR POWERVCR POWER
TV POWERTV POWER
TV
VCR
NTSC/PAL
MEMO
POWERPOWER
CH
CH
CH
1
1
1
1
While pressing the CDR/MD/TAPE remote control mode
selector button, input the 3-digit number (“000”, “111”
and “222”) corresponding to the device you want to
preset (CDR, MD or TAPE), referring to the table below.
• Release the CDR/MD/TAPE button after inputting
three digits. This completes the presetting operation.
Table 1: Combinations of Personal System Codes
Input the 3-digit number while pressing
CDR/MD/TAPE.
CDR/MD/TAPE
0
1
1
1
2
2
2
0
0
CDR
MD
TAPE
This is set to CDR by factory default.
NOTE:
• Only one device (CDR, MD or TAPE) can be stored in the
preset memory.
1
Press the CALL button while pressing the
TUNER/TV/VCR remote control mode selector button,
then input the three-digit number corresponding to the
code of the manufacturer of the TV whose signals you
want to store, referring to the included list of remote
control unit codes.
• Release the TUNER/TV/VCR button after inputting
three digits. This completes the presetting operation.
Example: To preset to “Hitachi 074”
Press the buttons below while pressing
TUNER/TV/VCR.
TUNER/TV/VCR
CALL
TV POWERTV POWER
0
7
4
HITACHI
“074”
This is set to “Hitachi 074” by factory default.
NOTE:
• Preset codes set upon shipment from the factory and
when reset.
 previous next