Filter
Top Products
47
ENGLISH
23
TROUBLESHOOTING
2Are all the connections correct ?
2Are you following the instructions in the manual ?
2Are the speakers and other components operating properly ?
If this unit does not seem to be functioning properly, check the table below. If this does not solve the problem, this unit may be
damaged. Turn off the power, unplug the power cord from the power outlet, and contact your store of purchase or nearest Denon
sales office.
Symptom Cause Measures Page
DISPLAY not lit and sound not
produced when power switch set to
on.
• Power cord not plugged in securely. • Check the insertion of the power cord
plug.
5
DISPLAY lit but sound not produced.
• Speaker cords not securely connected.
• Improper position of the audio function
button.
• Volume control set to minimum.
• MUTING is on.
• Digital signals not input Digital input
selected.
• Connect securely.
• Set to a suitable position.
• Turn volume up to suitable level.
• Switch off MUTING.
• Input digital signals or select input jacks
to which digital signals are being input.
8
19
19
20
19
Monitor doesn't display an image.
•
Connections between the video output
jack of this unit and the input connector
of the monitor are incomplete.
•
The input setting of the monitor TV is
different.
•
The video signals of the various devices
are not uniform.
•
Check whether the connections are
correct.
•
Set the input switching of the TV to the
jack to which the video input is
connected.
•
Make settings uniform for either
composite video or S-video connectors.
6, 7
—
6, 7
The program cannot be copied from
DVD to the VCR.
•
Almost all movie software contains a
copy prevention signal.
•
A copy cannot be made.
—
The subwoofer does not produce
sound.
•
Power is not being supplied to the
subwoofer.
•
The subwoofer setting is made to "No"
in the setup.
•
The output of the subwoofer has not
been connected.
•
Switch on the power of the subwoofer.
•
Change the setting to “Subwoofer” in
the setup.
•
Make the proper connections.
—
14
8
The test tone is not output.
•
The surround mode is set to a mode
other than auto decode.
•
Set to auto decode.
22
This unit does not operate properly
when remote control unit is used.
• Batteries dead.
• Remote control unit too far from this
unit.
• Obstacle between this unit and remote
control unit.
• Different button is being pressed.
• < and > ends of battery inserted in
reverse.
•
The mode selection of the remote
control is not properly selected. The
DVD mode, AV mode, or audio mode is
not properly selected.
• Replace with new batteries.
• Move closer.
• Remove obstacle.
• Press the proper button.
• Insert batteries properly.
•
Press the remote control mode
selection button for the item you wish
to operate. To operate this unit, use
with the DVD mode.
10
10
10
9
10
9
Remote control unit
Common problems when listening to the discs, tapes and FM broadcasts, etc.
Check again before assuming the player is malfunctioning
Symptom PageCheck
DVD operation
Playback does not start when PLAY
button is pressed.
Playback stops immediately.
—
4
5
• Is there condensation on the disc or player ? (Let stand for 1 or 2 hours.)
• Discs other than DVDs, video CDs and music CDs cannot be played.
• Disc is dirty. Wipe off the dirt.
Menu playback of video CD’s is not
possible.
—• Menu playback is not possible with anything but video CDs with playback control.
Picture is disturbed during the search
operation.
—• Some disturbance is normal.
Buttons do not operate. 18• Some operations are disabled for some discs.
No subtitles are displayed.
—
41, 42
• Subtitles are not displayed for DVDs not containing subtitles.
• Subtitles are turned off. Turn the subtitles setting on.
Audio (or subtitle) language does not
switch.
36
38
• The audio (or subtitle) language does not switch for discs which do not include multiple
audio (or subtitle) languages.
• For some discs the audio (or subtitle) language cannot be switched when the operation
to switch it is performed, but can be switched on the menu screens.
Angle does not switch.
37• The angle cannot be switched for DVDs which do not contain multiple angles. In some
cases multiple angles are only recorded for specific scenes.
Playback does not start when the
title is selected.
45• Check the “RATINGS SETUP” setting.
The password for rating level has
been forgotten.
Reset all the DVD setting to
Factory Preset.
45• While the player is in the stop mode, hold the player's SKIP (
8
) button and the
PAUSE
(3
) button down simultaneously for longer than 3 seconds (until “INITIALIZE”
disappears from the TV monitor).
The lock will be released and the DVD all default settings and picture settings will return
to the default values.
The disc is not played with the audio
or subtitle language set as the
default setting.
36• The disc does not play with the selected audio or subtitle language if that audio or
subtitle language is not included on that DVD.
Picture is not displayed in 4:3 (or
16:9).
43• Set the “TV ASPECT” default setting to the proper setting for the connected TV.
Menu screen messages for the
desired language do not display.
41, 42• Check the default setting for the disc language’s menu language.