Filter
Top Products
The subtitle language cannot be
changed or turned off.
The angles cannot be changed.
Recording does not stop immediately
after you
press
[STOP .1.
The
disc
tray
does
notopen when you
press
[OPEN/CLOSE
~I.
"Repairing" appears on the
TV
screen.
IliRi!III.I~Iffjt=._1
In
a
case
you intend
to
cancel the
repairing process.
~"
y",""S"
x : i
No image from HDMI connection.
There
is
no sound or the sound
is
distorted.
There
is
no picture.
Picture noise appears.
The cassette tape does
not
play back.
The
tape ejected after you
press
[RECel.
The remote control does
not
function.
The
motor
rotates even when
playback / recording
is
stopped.
NG
Remedy
•Multilingual subtitle are
not
recorded on the DVD-video.
•Multi-angles are
not
recorded on the DVD-video being played back.
•The angle-change operation
is
whenever possible
as
long
as
the disc
contains a multi-angle portion. Actual change will be performed when
the portion
has
come up.
•The DVD-video prohibits changing angles.
•Try changing the angle using the DVD-video's menu.
•It may take a few seconds for the
unit
to
input
disc data before
recording stops.
•It may take afew seconds for the disc tray
to
open after you have
recorded or edited a disc. This
is
because the
unit
is
adding disc data
to
the disc.
•If there
is
a power failure or unplugging during recording, finalizing,
formatting or editing (even after "Repairing" disappears). a repairing
process will begin automatically just after turning the
unit
on again.
It may take several minutes
up
to
about several hours.
•If you intend
to
cancel the repairing process, press
[~OPEN/CLOSEI
on the front panel, then select
"Yes"
and press [ENTERI. After that, press
[OPEN/CLOSE
~I
to
take
out
the disc. The disc canceled during
the
repairing process
MAY
NOT work.
•Check the HDMI connection. (Check the status
of
the HDMI related
indications.)
•Check whether the connected
monitor
device or other device supports
HDCP.
(This
unit
will
not
output
a video signal unless the otherdevice
supports
HDCP.)
•Check the setting
of
HDM!.
•Check whether the
output
format
of
this
unit
(HDMI
FORMAT)
matches
the supported
input
format
of
other connected device.
·If
the
unit
is
connected
to
the unauthorized display device
with
an
HDMI cable, the audiolvideo signal may
not
be
output
when playing
back a commercial DVD-video.
•The HDMI sound
is
not
output
when "HDMI Audio"
is
set
to
"OFF".
•Check the
RCA
audio cable connection.
If
you
are
using HDMI-DVI
conversion cable, you must connect the
RCA
audio cable, too.
•Check whether the
output
format
of
this
unit
(HDMI
FORMAT)
matches
the supported
input
format
of
other connected device.
·If
you connect the cable
to
S-VIDEO
OUT/
COMPONENT
VIDEO
OUT
/
HDMI
OUT
jack, try connecting
it
to
AUDIO /
VIDEO
OUT
jack instead.
•Head cleaning for
VCR
may be necessary. Refer
to
"Auto Head Cleaning"
(page
S).
•Adjust tracking control for better picture by pressing [TRACKING A /
VI
while you
are
playing back acassette tape.
•No cassette tape
is
inserted.
•Make sure the cassette tape
has
an erase-protection tab when you
record
to
a cassette tape.
If
needed, cover the hole
with
cellophane
tape.
•Check
if
a cassette tape
is
in this unit.
•The
motor
may rotate for the duration
of
approximately 5 minutes for
efficient operation. This
is
not
a malfunction.
104
EN