Filter
Top Products
Before recording from
DVC.
refer to page
44
for
connection instructions.
e
STOP
REC
[!J]
TOSHIBA
SE·R0295
Press [VCR] first.
Preparing for DV to
VCR
dubbing:
• Insert a recordable cassette tape and make
sure
your
DVC
is
in
video mode.
1
2
3
4
5
Repeat
the
steps 1 and 2 on page 47.
Press
the
PLAY
button on your DVC
to
find where you wish
to
start
dubbing. Then, press
the
PAUSE
button
on
the
DV camcorder when
you come
to
the
desired start point.
Press
[REC
e]
to
start recording.
Press
the
PLAY
button
or
the
PAUSE
button on your DVC
to
resume
the
playback.
The
dubbing
will start.
To
pause the recording:
Press
[PAUSE
II] once.
"REC"
will flash.
To resume recording:
Press
[REC
e]
or press
[PAUSE
II] again.
"REC"
will reappear.
To stop recording, press [STOP
.].
Note for
DV
dubbing
'''''''''''''''~''''~''m''''''-'''·,_
....
,
=.",......
""'-
"'.....,.'~,..1
•
If
you press
[PAUSE
II] at step 5 in
"DVC
to
DVD
Dubbing" on page
47,
the tape will rewind
to
the
point
a
few"
seconds preceding the paused point. When you press
[ENTER]
at step 6 in
"DVC
to
DVD
Dubbing" on page 47, .
then,
it
will start
dubbing
when
it
comes
to
the paused point. j
• The
unit
does
not
send
out
the
output
signal
to
DVC.
I
.•
For the proper operation, connect
DVC
to
the
unit
directly.
Do
not
connect this
unit
and
DVC
via any other unit. J
• Do
not
connect more than 1
DVC.
i
• The
unit
can
only accept
DVC.
Other
DV
device such
as
cable/satellite box or
D-VHS
VCR
cannot be recognized. I
• If no video signal
is
detected from
the
DVC
during
DVC
to
DVD
dubbing, the recording will be paused and
"e"
will
~
flash on the
TV
screen. The recording will resume when the
unit
detects the video signal again.
~
• When the
DVC
is
in
camera mode, refer
to
"Guide
to
DV
and On-Screen Display" on page
46.
I
•
You
cannot
dub
from
DVC
during timer standby mode. I
•
You
cannot
dub
from
DVC
to
the both
DVD
and
VCR
at the same time.
.'
•
You
cannot change the
output
mode during
DVC
to
VCR
dubbing.
If
you want
to
switch
to
the
DVD
mode, stop
the
VCR
first.
• During
DVC
to
VCR
dubbing, you cannot change channels while paused. I
• When
output
is
in
DVD
mode while playing back a
DVD
using DV(L3l. you cannot switch
to
the
VCR
mode.
. • Ifyou
are
using anything other than
DV(L3)
to
playback
DVD,
you
can
switch
to
the
VCR
mode,
but
cannot select
DV(L3)
channel.
(You
can
select
DV(L3)
after sWitching
to
the
DVD
mode during
VCR
playback.)
.•
During timer standby
of
either component, you cannot select
DV(L3)
even on
the
component which
is
not
in timer
•..
m~~
.
• Date / time and cassette memory data will
not
be recorded.
• Pictures
with
a copy-guard signal cannot be recorded.
• A
DV
terminal
is
a terminal
that
can
use
the transmission mode conforming
to
the
IEEE
1394 standards called "Fire
Wire". It serves
as
the interface that connects the
PC
and peripheral device such
as
"LLink" (registered trademark
of
.
SONY).
It enables digital
dubbing
between
DV
devices
with
little degradation. .
jf;,
"",....-4l."
'-&ttl}.'
48
EN