Filter
Top Products
•
If
there
is
a power failure
or
this
unit
has
been
unplugged for more than
30
seconds, the clock setting
and all timer programming will be lost.
•
If
a disc
is
not
inserted or
if
a inserted disc
is
not
recordable (finalized
DVD-RW/-R,
finalized
DVD+RW,
a
fully recorded disc, etc.), "DVD" on the front panel
display flashes and
timer
recording cannot be
performed.
In
some
cases,
~
will appear momentarily
around the start
point
as
the
unit
attempts
to
record.
Please
insert a recordable disc.
•
If
a cassette tape
with
an
erase-protection tab
is
not
in
the cassette compartment
or
there
is
no cassette tape in
the cassette compartment,
"VCR"
on the front panel
display flashes and timer recording cannot be
performed.
Please
insert a recordable cassette tape.
•
If
you press [TIMER
SET]
and turn on the
unit
while
either
DVD
or
VCR
is
in timer standby mode,
~
disappears.
In
this
case,
you cannot change the mode
between
DVD
and
VCR.
You cannot change any settings
using [SETUP]
or
edit discs.
•When
all
the timer recording
is
completed,
~
flashes.
To
play back or eject the recorded
disc,
press
[I/O
ON/STANDBY] first, then select the recorded title and
press
[PLAY
~],
or
[OPEN/CLOSE~]
to remove the
disc.
• During timer recording
or
timer standby mode
(~will
appear), any operations on the
unit
will
not
be available.
To
make these operations available, press
[.
STOP] on
the
front
panel
to
cancel the
timer
recording
or
[TIMER
SET]
to
release
timer
standby mode
(~will
disappear).
•To cancel the timer standby mode, press [TIMER
SET].
• When the starting and the ending time are the
same,
"Exceeds
12
hours" appears and the program setting will
not
be accepted.
• When the programmed starting and ending time are
earlier than the current time, the setting will
not
be
accepted.
•
If
the starting time
is
earlier and the ending time
is
later
than the current time, the recording will start right after
[TIMER
SET]
is
pressed.
•The
timer
recording cannot be performed in
DVD
and
VCR
at the same time.
If
you set 2 programming
with
the
same channel and time in both devices, the program
with
a lower program number will
be
recorded.
The Priority
of
Overlapped Settings
This
unit
records the programs according
to
priority
if
the timer programmings are overlapped. The
timer
programming set previously
has
priority.
A timer recording
of
lower priority will be canceled
or
start from the middle.
Check the overlapped
timer
programmings and change the priority
if
necessary.
•
When
the startingtime
is
the
same:
• When
the
starting
time
and the ending
time
A
program
set
previously
(PROG.
A)
has
priority.
for
each programs are different:
A
program
that
has
earlier start time
has
priority.
PROG.A
PROG.B
• When the recording time
is
partiallyoverlapped:
PROG.
Awill start after
PROG.
B
is
complete to
be
recorded.
PROG.A
• When the recording time
is
entirelyoverlapped:
PROG.A
will not
be
recorded.
PROG.B
Note
forDVD
recording
o When
the
recording
time
of
2 programs are overlapped,
or
the
end
time
of
a program and
the
start
time
of
another
program
is
the same, the first 2 minutes (at
the
longest)
of
the
subsequent program will be cut off.
o
If
the
cut-off
portion
comes
up
to
3 minutes
or
more, this
program will be displayed
with
errors
number
E40
in
the
timer
programming, list.
• When
the
end
time
of
the
programming
currently
being recordedand
the
start
time
of
the
subsequentprogram aresame:
The
beginning
of
the
PROG.
Bmay
be
cut off.
EN
41