Filter
Top Products
49-EN
Parametric Equalizer Adjustments
The frequency bands of the graphic equalizer are fixed. This makes it
very difficult to correct for undesired peaks and dips at specific
frequencies. The parametric equalizer’s centre frequency can be tuned
to these specific frequencies. Then, the bandwidth (Q) and level are
fine-tuned, independently, to make the necessary corrections. The
parametric equalizer function is an advanced tool for serious
audiophiles.
1
Check that Defeat mode is off (page 20) and P.EQ is
selected in “Setting User’s EQ mode” (page 21).
2
Press and hold MENU for at least 2 seconds.
3
Select the Parametric EQ mode by sliding your
finger on the GlideTouch bar to the left or right.
Press the GlideTouch bar under the Parametric
EQ mode.
4
Select L+R or L/R by pressing and holding BAND
for at least 2 seconds.
L+R: Sets the same adjustment values for the left and
right channels.
L/R: Different adjustment values can be set for the left
and right channels.
When graphic EQ is adjusted, this setting will be turned
off.
5
Select the desired channel by sliding your finger
on the GlideTouch bar to the left or right. The
channel changes by pressing the GlideTouch
bar.
6
Press BAND to select the band.
7
Select the frequency sliding your finger on the
GlideTouch bar to the left or right. Press the
GlideTouch bar under the frequency.
8
Press SOURCE/POWER to set the band width (Q).
9
Adjust the level by turning the Rotary encoder.
10
To adjust other bands, repeat steps 6 to 9.
11
When the setting is complete, press and hold
MENU for at least 2 seconds.
• When the speaker is set to the “OFF” mode, the parametric
equalizer for that speaker cannot be set. Refer to “Setting the
Speakers” (page 46).
• It is not possible to adjust the frequencies of adjacent bands within
7 steps.
• Check the playable frequency ranges of the connected speakers
before making the equalizer adjustments. If the speaker’s playable
frequency range is 55 Hz to 30 kHz, for example, adjusting the
40 Hz or 20 Hz band has no effect. Additionally, you may overload
and damage the speakers.
• When the parametric EQ is adjusted, the adjustment for graphic
EQ becomes ineffective.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 53.
Setting Bass Compressor
You can adjust the sound of low frequencies as desired.
1
Check that Defeat mode is off (page 20).
2
Press and hold MENU for at least 2 seconds.
3
Select the BASS COMP. mode by sliding your
finger on the GlideTouch bar to the left or right.
Press the GlideTouch bar under the BASS COMP.
mode.
4
Touch the GlideTouch bar, and select the desired
mode by sliding your finger to the left or right, then
press the GlideTouch bar.
Bass sound is emphasized more as the mode is
sequentially switched as MODE1 → 2 → 3, offering you
vivid low frequencies.
Select OFF when the setting is not necessary.
5
When the setting is complete, press and hold
MENU for at least 2 seconds.
Speaker Setup
The PXA-H700 or PXA-H701 can be set according to the playable
frequency range of your speakers.
Check the playable frequency range of the speakers (not including the
subwoofer) before performing this operation to verify whether the
speakers can play low frequencies (of about 80 Hz or less).
• Avoid stopping, pausing, switching the disc, cueing, fast-
forwarding or switching the audio channel of this unit while
making this adjustment. The setting is cancelled if Decode mode is
switched.
1
Check that Defeat mode is off (page 20).
2
Press and hold MENU for at least 2 seconds.
3
Select the Speaker Setup mode by sliding your
finger on the GlideTouch bar to the left or right.
Press the GlideTouch bar under the Speaker
Setup mode.
4
Touch the GlideTouch bar, and select the speaker
by sliding your finger to the left or right, then press
the GlideTouch bar.
5
Select the speaker characteristic by sliding your
finger on the GlideTouch bar to the left or right.
Press the GlideTouch bar under the speaker
characteristic.
OFF*
1
: When no speaker is connected.
SMALL: When a speaker that cannot play low
frequencies (80 Hz or less) is connected.
LARGE*
2
: When a speaker that can play low frequencies
(80 Hz or less) is connected.
*
1
It is not possible to set the front speakers to “OFF”.
*
2
If the front speakers are set to “SMALL”, the rear and
centre speakers cannot be set to “LARGE”.
Continued