JVC KDC-BT92SD Car Stereo System User Manual


  Open as PDF
of 41
 
25
|
KDC-BT92SD
English
|
26
Getting Started of Bluetooth
Easy pairing function
1
Enter easy pairing mode
Press the [ ] button for at least 1 second.
Any of the following is displayed depending on
Bluetooth device registration condition:
– “Searching”: When registering a Bluetooth device
for the first time.
– “(Bluetooth device name)”: When a Bluetooth
device has already been registered.
– “Device Full”: When maximum of five Bluetooth
devices have already been registered.
When registering a Bluetooth device for the
first time (Registering a Bluetooth device)
2
“Searching” is displayed.
Search for the Bluetooth device.
When search is completed, “Finished” is displayed.
3
Select a Bluetooth device name
Turn the [VOL] knob and press it when the
desired item is displayed.
“Confirm Device” is displayed.
If “Pairing Success” is displayed, proceed to step 7.
If “PIN code” is displayed, proceed to steps 5.
If“***NG”isdisplayed,pressthevolumeknob.
Proceed to steps 4.
5
Input the PIN code
1. Turn the [VOL] knob and press it when the
desired item is displayed.
Select the digit.
2. Turn the [VOL] knob to select the numbers,
and then press the [VOL] knob.
6
Transmit the PIN code
Press the [VOL] knob for at least 1 second.
If “Pairing Success” is displayed, registration is
completed.
When “Confirm Device” is displayed, confirm
connection with a Bluetooth device operation.
7
The receiver is connected to a Bluetooth
device, with “HF CONNECT” or “AUDIO
CONNECT” displayed, and exits the easy
pairing mode.
⁄
• Ifanerrorcodeisdisplayedduringparing,see
<TroubleshootingGuide>(page77).
When a Bluetooth device has already been
registered, or maximum of five Bluetooth
devices have already been registered/ selecting
a Bluetooth device
2
“(Bluetooth device name)” or “Device Full” is
displayed.
3
Select a Bluetooth device name
Turn the [VOL] knob.
✍ To register a new Bluetooth device, select
“Device Search”, then go to <When registering a
Bluetooth device for the first time>.
4
Press the [VOL] knob.
5
Select the profile for the device to connect
Turn the [VOL] knob.
✍ “HF”(HFP),“AUD”(A2DP),or“H&A”(HFPandA2DP)
indicates the corresponding profile.
6
Set up the Bluetooth device name
Press the [VOL] knob.
“✱H✱A (device name)”: The selected Bluetooth
device is busy.
“-H-A (device name)”: The selected Bluetooth
device is on standby.
“ “ (blank) (device name): The Bluetooth device is
deselected.
✍ If a Bluetooth device is already selected, deselect
it, and then select a different one.
✍ “H”(HFP)or“A”(A2DP)indicatesthecorresponding
profile.
7
Exit easy pairing mode
Press the [ ] button.
Deleting the registered Bluetooth device
2
“(Bluetooth device name)” or “Device Full” is
displayed.
3
Select a Bluetooth device name
Turn the [VOL] knob.
4
Delete the selected Bluetooth device
Press the [VOL] knob for at least 2 seconds.
SRC VOL
5
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
Registering from Bluetooth devices
(Pairing)
To make your Bluetooth device (cell-phone) usable
with this unit, you need to register it (pairing). You
can register up to 5 Bluetooth devices to this unit.
1
Turn on this unit
Press the [SRC] button.
Start registering this unit by operating the
Bluetooth device.
By operating the Bluetooth device, register the
hands-free unit or audio unit (pairing). Select
“KENWOOD BT CD/R-6P1” from the list of found
units.
3
Enter a PIN code
Input the PIN code (“0000”) in the Bluetooth
device.
Check that registration is complete on the
Bluetooth device.
✍ PINcodeissetto“0000”asthedefault.Youcan
change this code. Refer to <Registering PIN
Code> (page 56).
By operating the Bluetooth device, start
hands-free connection.
⁄
• Ifthereare5ormoreBluetoothdevicesregistered,you
cannot register a new Bluetooth device.
 previous next