Filter
Top Products
49
|
KDC-BT92SD
English
|
50
DSP Setup
Listening Position Fine Adjustments
Adjusting fine tuning of the speaker position
compensation value specified at <Car Type
Selection> (page 47).
Display Item Range
“FRONT” Front speaker
0 – 610 cm
“REAR” Rear speaker
0 – 610 cm
“SW” Subwoofer
0 – 610 cm
( : Factory setting)
1
Select the source
Pressing the [SRC] button repeatedly switches
source.
Select a source other than “STANDBY”.
✍ SRC Select mode 2: Press the [SRC] button and
then turn the [VOL] knob. To determine the
selected source, press the [VOL] knob.
2
Enter Audio Control mode
Press the [VOL] knob.
3
Enter Manual position setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Pro Setup” > “DTA Settings” > “ D TA”.
4
Select the speaker you want to set
Turn the [VOL] knob and press it when the
desired value is displayed.
Item Setting overview
“DTA FRONT” / “L” Front Left speaker
“DTA FRONT” / “R” Front Right speaker
“DTA REAR” / “L” Rear Left speaker
“DTA REAR” / “R” Rear Right speaker
“DTA SW / “L” Subwoofer Left
“DTA SW” / “R” Subwoofer Right
5
Set the value
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
The settings of the delay time are automatically
identified and compensated by specifying the
distances of each speaker from the center of the
vehicle interior.
1Setthefrontandrearpositionsandtheheight
of the reference point to the position of the ears
of the person sitting in the front seat, and set
the right and left positions to the center of the
vehicle interior.
2 Measure the distances from the reference point
to the speakers.
Listening Position Selection
The sound environment can be compensated in
accordance with the selected position. According to
the listening position, select the position from the
following settings.
Display Compensation seat
“ALL” Not compensating.
“Front-Left” Front-Left seat
“Front-Right” Front-Right seat
“Front” Front seat
( : Factory setting)
1
Select the source
Pressing the [SRC] button repeatedly switches
source.
Select a source other than “STANDBY”.
✍ SRC Select mode 2: Press the [SRC] button and
then turn the [VOL] knob. To determine the
selected source, press the [VOL] knob.
2
Enter Audio Control mode
Press the [VOL] knob.
3
Enter Preset position setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Pro Setup” > “DTA Settings” > “Preset
Position”.
4
Select the seat you want to compensate
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
5
Exit Audio Control mode
Press the [MENU] button for at least 1 second.
3 Calculate the distance difference in accordance
with the farthest speaker.
Reference point
FRONT
FRONT
SUB-W
REAR
REAR
6
Exit Audio Control mode
Press the [MENU] button for at least 1 second.
Channel Level Fine Adjustments
After DTA compensation, you can finely adjust
the unsatisfactory speaker volume of respective
speaker.
Display Item Range
“FRONT” Front speaker
“–8” — “0”
“REAR” Rear speaker
“–8” — “0”
“SUBWOOFER” Subwoofer
“–8” — “0”
( : Factory setting)
1
Select the source
Pressing the [SRC] button repeatedly switches
source.
Select a source other than “STANDBY”.
✍ SRC Select mode 2: Press the [SRC] button and
then turn the [VOL] knob. To determine the
selected source, press the [VOL] knob.
2
Enter Audio Control mode
Press the [VOL] knob.
3
Enter Channel Level setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Pro Setup” > “DTA Settings” > “Channel
L ev e l”.
4
Select the speaker you want to set
Turn the [VOL] knob and press it when the
desired value is displayed.
Item Setting overview
“CHANNEL LEVEL.
FRONT” / “L”
Front Left speaker
“CHANNEL LEVEL.
FRONT” / “R”
Front Right speaker
“CHANNEL LEVEL.
REAR” / “L”
Rear Left speaker
“CHANNEL LEVEL.
REAR” / “R”
Rear Right speaker
“CHANNEL LEVEL.
SUBWOOFER” / “L”
Subwoofer Left
“CHANNEL LEVEL.
SUBWOOFER / “R”
Subwoofer Right
5
Set the value
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
6
Exit Audio Control mode
Press the [MENU] button for at least 1 second.