Filter
Top Products
30
206-4278
097 - AUDIO OUTPUT
Determines availability and signal type/level (xed speaker,
variable speaker, or xed line level [amplier]) of the audio
output to be used by external audio equipment connected to the
SPEAKER OUT / LINE OUT jack on the TV. Set to 0 to disable
audio output. Otherwise, see the table below and set as required
in accordance with audio equipment. See also Reference section,
“External Stereo Speaker Specifications.”
Value Status
Speaker Output 1 Fixed 0.01 Watts
2 Fixed 0.03 Watts
3 Fixed 0.05 Watts
4 Fixed 0.10 Watts
5 Fixed 0.20 Watts
6 Fixed 0.50 Watts
7 Fixed 1.00 Watt (default)
8 Control with volume
Line Output 9 Fixed line level (typically 400 mVrms ±
100 mVrms @10KΩ) output
098 - PRO:CENTRIC
Selects the Pro:Centric Application Mode. Set to 0 (default) to
disable the Pro:Centric application. Set to 1 for Flash Mode. Set
to 2 for GEM (Java Application) Mode.
The TV must be turned OFF for a few seconds to initiate the
Pro:Centric application download. When the TV is turned back ON,
it may take several minutes to load the Pro:Centric application after
the initial download.
Note: This item is not available in the Installer Menu when item
119 DATA CHANNEL is set to 0.
099 - BACK LIGHTING
Sets the TV screen brightness at power up. Default setting is 255.
• 1 - 100 Static Back Lighting
(1 = Dimmest picture, 100 = Brightest picture)
• 101 - 200 Dynamic Back Lighting
(101 = Dimmest picture, 200 = Brightest picture)
If set between 101 and 200, the TV automatically controls back
lighting depending upon the picture level of the current program. If
set to 255, back lighting is controlled via the Picture settings in the
TV setup menus.
102 - ATSC BAND
Sets up TV to receive different types of incoming signals.
0 = Broadcast 1 = CATV 2 = HRC
3 = IRC 4 = Same as NTSC
103 - ATSC TUNE MODE
Sets ATSC tuning mode. Default set to 1 for Physical Channel
scan. Set to 0 for Virtual Channel scan.
104 - START MINOR CHANNEL
Sets Minor Start Channel number at power up. 0 = NTSC. If not
0, number selected is the digital channel’s Minor Start Channel
number.
Note: This item is not available in the Installer Menu when item
004 STRT CHANNEL is set to 0 or 255.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 1 to retain previous aspect ratio with power off. Set to 0 to
retain default aspect ratio with power off. See item 096 DEF. ASP.
RATIO above.
116 - VIDEO MUTE EN (Video Mute Enable)
Applicable for analog channels only. If set to 1, video mutes
(blank screen) when no signal is present.
117 - FACT DEFAULT (Factory Default)
Set to 1 and press OK to restore the factory default settings of all
Installer Menu items. Once complete, the value returns to 0.
Caution: If set to 1, this clears all Installer Menu custom
settings and restores the factory default settings. It also
clears the channel lineup, including any assigned
channel icons and custom text labels.
Note: See also Reference section, “Restoring Factory Defaults on
the TV(s),” for further information.
118 - POWER SAVINGS
Default set to 3—the power circuitry for both the embedded b-LAN
module and the GAME CONTROL/MPI port is only powered when
the TV is turned ON. When the TV is turned OFF, the embedded
b-LAN and the GAME CONTROL/MPI port are not powered.
Note that the TV must be turned ON in order to communicate with
the embedded b-LAN module for conguration and control when
POWER SAVINGS is set to 3. If POWER SAVINGS is set to 1,
the b-LAN module is always powered.
Similarly, if MPI communication is required for external MPI
control, POWER SAVINGS should be set to 1 so that the GAME
CONTROL/MPI port circuitry is always powered.
Note: See Reference section, “b-LAN Setup & Overview,” for
further information.
Caution: POWER SAVINGS should NEVER be set to 7.
This setting is intended for factory use only.
Installer Menu (Cont.)