Filter
Top Products
SET UP
23
En
OPERATION
Remote Control
These pages describe the buttons on the remote control
used to operate the amplifier.
6 MULTI CONTROL buttons
Use these buttons to select the remote operation
mode.
For example, pressing TUNER sets the remote to
operate the tuner functions.
7 Number buttons
These buttons can perform a variety of different
functions depending on the remote operation mode.
• [AMPLIFIER operations (press AMP first)]
: Switches the Dolby Surround mode on or
off(refer to page 29).
DSP MODE : Press repeatedly to select a DSP sound
mode (refer to page 26, 30).
MIDNIGHT : Press to hear surround sound effectively
at low volumes (refer to page 31).
CH.SELECT : Use to select a speaker when adjusting
speaker levels.
TEST TONE : Press to switch the test tone on or off
when listening to a surround mode (refer to page 19).
ATT : Press to attenuate (lower) the level of the input
signals and prevent distortion (refer to “Display”, 5,
Overload indicator on page 22).
SIG.SELECT : When the same component uses both
analog and digital connections, use to select input
signals as digital or analog.
CH.LEVEL (–/+) : Use to adjust individual speaker
levels after having pressed CH. SELECT to select a
speaker channel.
EFFECT (–/+) : Use to adjust the DSP mode effect level.
8 FUNCTION button
Press repeatedly to select a source.
9 MODE CHECK button
Press to confirm the current remote operation mode
and to switch operation modes without changing the
source (refer to page 41).
0 Power button
Press to turn on or put in standby all connected
components other than this unit.
- TV, TV FUNC button
Press TV to turn the TV’s power on or put in standby.
Press TV FUNC to select the TV for remote control
operation.
= AMP button
Press to select the amplifier for remote control
operation.
~ FL DIMMER button
Press to adjust the brightness of the fluorescent
display. Four levels of brightness ranging from very
dim to very bright can be selected.
! COMMANDER SET UP button
Use to customize the remote control functions.
(Refer to “Setting Up the Remote Control” starting on
page 20).
@ DIRECT button
Use to playback original source audio. When DIRECT
is ON, Dolby Surround, DSP, LOUDNESS, and
MIDNIGHT mode are automatically turned OFF.
1 AMP button
Press to switch the amplifier on or to put in standby.
2 MUTING button
Press to mute the volume. “MUTING” appears in the
display. Press again to cancel.
3 [When set to SURROUND]
@, #,%, fi, (Select/Adjust) buttons
[When set to other than OPERATIONS]
*(Pause), &(Stop), !(Rewind), ⁄(Fast Forward),
ENTER/‹(Play) buttons
[Tuner Operations]
FQ + (to higher frequencies), FQ – (to lower
frequencies), !(MPX), ⁄(DISP MODE), # (FM/AM)
buttons
!(MPX): Use to switch the auto stereo/monaural
mode for receiving FM broadcasts. When the
received broadcast signal is weak, press this button
to set the monaural mode.
⁄(DISP MODE): Use to switch the RDS data while
listening to an FM station. Each press changes the
display in the order of RT, PS, PTY, and frequency.
4 VOL (–/+) buttons
Press to adjust the volume. When VOL (–/+) buttons
are pressed while muting, muting is canceled.
5 CHANNEL (–/+) button
Use to select preset stations when operating the
tuner. When the remote is used to control other
components, this button may be used to change
channels, tracks, or chapters.
Names of Parts and Basic Operations
DVD/LD
VCR 1
TV/SAT
CD
TUNER
VCR 2
MD/TAPE
TV CONTROL
AMP
DSP MODE
CH.SELECT
ATT SIG.SELECT
MIDNIGHT
TEST TONE
AUDIO/VIDEO PRE-PROGRAMMED
REMOTE CONTROL UNIT
2
3
5
0
6
9
+10
TV/VCRCLASS
7
8
4
1
CHANNEL
MULTI CONTROL
ENTER
VOL VOL
FQ
FQ
+
–
TV FUNC
AMP
TV
MUTING
CH.LEVEL
EFFECT
FL DIMMER FUNCTION DIRECT
MODE CHECK
COMMANDER
SET UP
Î
MEMU
1
2
3
4
5
6
7
8
9
0
-
=
~
!
@