Filter
Top Products
Notes
! Listening to the radio while connecting a USB
storage device to this unit may generate
noise. In this case disconnect the USB sto-
rage device.
! When this unit’s blue/white lead is connected
to the vehicle’s auto-antenna relay control
terminal, the vehicle’s antenna extends when
this unit’s source is turned on. To retract the
antenna, turn the source off.
Use and care of the remote
control
Using the remote control
1 Point the remote control in the direction ofthe
front panel to operate.
When using for the firsttime, pull out the film
protruding from the tray.
Replacing the battery
1 Slide the tray outon the back of the remote con-
trol.
2 Insert the battery with the plus (+)and minus (–)
poles aligned properly.
Important
! Do not store the remote control in high tem-
peratures or direct sunlight.
! The remote control may not function properly
in direct sunlight.
! Do not let the remote control fall onto the
floor, where it may become jammed under the
brake or accelerator pedal.
WARNING
! Keep the battery out of the reach of children.
Should the battery be swallowed, consult a
doctor immediately.
! Batteries (battery pack or batteries installed)
must not be exposed to excessive heat such
as sunshine, fire or the like.
CAUTION
! Use one CR2025 (3 V) lithium battery.
! Remove the battery if the remote control is not
used for a month or longer.
! There is a danger of explosion if the battery is
incorrectly replaced. Replace only with the
same or equivalent type.
! Do not handle the battery with metallic tools.
! Do not store the battery with metallic objects.
! If the battery leaks, wipe the remote control
completely clean and install a new battery.
! When disposing of used batteries, comply
with governmental regulations or environmen-
tal public institutions’ rules that apply in your
country/area.
Menu operations identical
for function settings/audio
adjustments/initial
settings/lists
Returning to the previous display
Returning to the previous list(the folder one level
higher)
1 Press
.
Returning to the mainmenu
1 Press and hold
.
Returning to the ordinary display
Canceling the initial setting menu
1 Press B(BAND/ESC).
En
10
Section
02
Operating this unit
Tuner
Basic operations
Selecting a band
1 Press B(BAND/ESC) until the desiredband (F1,
F2, F3 for FMor AM) is displayed.
Manual tuning (step by step)
1 Press cor d.
Seeking
1 Press and holdc or d, and then release.
You can cancel seek tuning bybriefly pressing c
or d.
While pressing and holding cor d, you can skip
stations. Seek tuning starts assoon as you re-
lease c or d.
Storing and recalling stations
for each band
Using preset tuning buttons
1 When you find a station that you want
to store in memory, press one of the preset
tuning buttons (1 to 6) and hold until the
preset number stops flashing.
2 Press one of the preset tuning buttons
(1 to 6) to select the desired station.
# You can also recall stored radio stations by
pressing a or b during the frequency display.
Function settings
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
3 Turn M.C. to select the function.
After selecting, perform the following proce-
dures to set the function.
BSM (best stations memory)
BSM (best stations memory) automatically stores the
six strongest stations in theorder of their signal
strength.
1 Press M.C. toturn BSM on.
To cancel, press M.C. again.
LOCAL (local seek tuning)
Local seek tuning lets youtune in to only those radio
stations with sufficiently strong signals forgood re-
ception.
1 Press M.C. todisplay the setting mode.
2 Turn M.C. to selectthe desired setting.
FM: OFF—LEVEL 1—LEVEL 2—LEVEL 3—LEVEL
4
AM: OFF—LEVEL 1—LEVEL 2
The highest level setting allows reception of only
the strongest stations, while lower levels allow the
reception of weaker stations.
3 Press M.C. toconfirm the selection.
En
11
Section
02
Operating this unit
Operating this unit
<QRB3172-A/N>6