Filter
Top Products
68-EN
Antenna Receptacle
ISO/JASO Antenna Adapter (sold separately)
ISO/JASO Antenna Adaptor may be required, depending on
the vehicle.
Video Input Connector (AUX IN) (Yellow)
Input the AUX video.
• To use this function, turn on “AUX1 IN” in the “SETUP” menu (see
“Setting the AUX Mode” on page 40).
Audio Input Connector (AUX IN)
RED is down and WHITE is up input the audio.
Video Output Connector (AUX OUT) (Yellow)
Output the video.
Audio Output Connectors (AUX OUT)
RED is down and WHITE is up output the audio.
Front Output RCA Connectors
RED is left and WHITE is right.
Rear Output RCA Connectors
RED is left and WHITE is right.
Subwoofer Output RCA Connectors
RED is left and WHITE is right.
Fuse Holder (15A)
Power Supply Connector
Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle’s fuse
box or another unused power source which provides (+)
12V only when the ignition is turned on or in the accessory
position.
Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
Power Antenna Lead/Remote Turn On Lead (Blue/
White)
Connect this lead to the +B terminal of your power antenna,
if applicable.
Also connect this lead to the remote turn-on lead of your
amplifier or signal processor.
Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle’s
battery.
ISO Power Supply Connector
ISO Connector (Speaker Output)
Left Rear (+) Speaker Output Lead (Green)
Left Rear (–) Speaker Output Lead (Green/Black)
Left Front (+) Speaker Output Lead (White)
Left Front (–) Speaker Output Lead (White/Black)
Right Front (–) Speaker Output Lead (Grey/Black)
Right Front (+) Speaker Output Lead (Grey)
Right Rear (–) Speaker Output Lead (Violet/Black)
Right Rear (+) Speaker Output Lead (Violet)
Parking Brake Lead (Yellow/Blue)
Connect this lead to the power supply side of the parking
brake switch to transmit the parking brake status signals to
the IVE-W530BT.
Reverse Lead (Orange)
Use only when a back-up camera is connected. Connect to
the plus side of the car’s reverse lamp. This lamp illuminates
when the transmission is shifted into reverse (R).
With this lead properly wired, the video picture
automatically switches to the back-up camera whenever the
car is put into reverse (R).
Remote Control Output Lead (White/Brown)
Connect this lead to the remote control input lead. This lead
outputs the controlling signals from the remote control.
RGB Input Connector
Connect this to the RGB output terminal of the Navigation
System.
USB Connector
Connect this to a USB Memory device or to an iPod/iPhone.
To use an iPod/iPhone, an iPod interface cable is required.
• Use the supplied USB cable. If a USB cable other than the supplied is
used, correct performance cannot be guaranteed.
• Route the USB cable away from other cables.
MIC Input Connector
To Microphone
Steering Remote Control Interface Connector
To steering remote control interface box.
For details about connections, consult your nearest Alpine
dealer.
iPod (V)/AUX Input Connector
Input the iPhone/video compatible iPod audio/video signal
or AUX video/audio signal.
• Set “AUX2 IN” to “iPod Video” in “Setting the AUX Mode”
(page 40) when an iPhone or a video compatible iPod is connected.
• Set “AUX2 IN” to “AUX” in “Setting the AUX Mode” (page 40)
when normal AUX video/audio is input.
CAMERA Input Connector
Use when the optional rearview camera with RCA
Connector is connected.
• Set “ON” in “Setting the Rear Camera Input” (page 39) when
connecting a rearview camera with RCA output connector.
RCA Extension Cable (sold separately)
Microphone (Supplied)