Filter
Top Products
29
<Basic command list>
No. Commands Functions Data
1
!
**
*1
B C N 1 Cr Starts communication (connection) No data
2
!
**
*1
B C N 0 Cr Terminates communication (termination) No data
3
!
**
*1
BIDS E T x x
*2
Cr Assigns the control ID 01 – 99
4
!
**
*1
B I D R E T Cr Initializes the control ID No data
5
!
**
*1
BIDDS P x x
*2
Cr Displays/hides the ID
00: Hide
01: Display
6
!
**
*1
BIDCH K x x
*2
Cr Flashes/hides the selected ID No. of the monitor
00: Hide
01: Display
7
!
**
*1
B M E N U Cr Displays the MAIN MENU/Quits the menu operation No data
8
!
**
*1
BUPCr
Moves the cursor downward (
)
No data
9
!
**
*1
BDOWN Cr
Moves the cursor downward (
)
No data
10
!
**
*1
BADJ R Cr
Makes setting/adjustment (
)
No data
11
!
**
*1
BADJ L Cr
Makes setting/adjustment (
)
No data
12
!
**
*1
B S E T U P Cr Displays the SET-UP MENU No data
13
!
**
*1
B P W 1 Cr Turns on the monitor No data
14
!
**
*1
B P W 0 Cr Turns off the monitor (on standby) No data
15
!
**
*1
B I N A Cr Selects “SDI 1/L” input No data
16
!
**
*1
B I N B Cr Selects “SDI 2/R” input No data
17
!
**
*1
B I N C Cr Selects “DVI” input No data
18
!
**
*1
B D I S P Cr Displays the status *
3
No data
19
!
**
*1
BAMU T E x x
*2
Cr Turns muting on/off
00: Off
01: On
20
!
**
*1
BASP x x
*2
Cr Changes the aspect ratio
00: 4:3
01: 16:9
21
!*
*
*1
BROP O S I x x x x
*2
Cr Configures POSITION settings −999 – +999
22
!*
*
*1
BROP U S H x x
*2
Cr Configures PUSH SEL. settings
00: Change selection,
01: Reset the position
23
!*
*
*1
B S E L E C T Cr Operates the SELECT keys No data
24
!*
*
*1
B3DS C A L E x x
*2
Cr Changes 3D cursor mode
00: Off
01: Cursor mode
02: Grid mode
25
!*
*
*1
B3Dxx
*2
Cr Changes 3D mode
00: Off
01: On
26
!*
*
*1
B C A M E R A Cr Displays the CAMERA ASSIST MENU No data
27
!*
*
*1
BMI X x x
*2
Cr Changes MIX mode
00: Off
01: On
● “Cr” is 0Dh.
● The commands for starting communication (connection) (No. 1), terminating communication (termination) (No. 2), and turning on the
monitor (No. 13) can be used while the monitor is off (on standby).
*1
Enter the monitor’s ID for “**.” The initial setting of the monitor’s ID is “00.” When connecting several monitors, “00” is a command for
controlling all monitors at once.
*2
Enter the appropriate data to “xx.”
*3
Displays the information shown when the INPUT SELECT button currently lit is pressed (→ “On the Status Display” on page 11).