Filter
Top Products
14-EN
01GB06PXAH800.fm
ALPINE PXA-H800_EN 68-13530Z65-A (B5)
From a PC
• Speakers that cannot be turned off do not show “OFF. ” Refer to
Table 1 (Output System) in “System Configuration” (page 60).
• If the speaker system is changed, all setup values except those for
AUX input will be restored to the initial setup values.
• You can also set the speakers from “Setting the Speakers (Speaker
Setup)/Setting the Subwoofers” (page 14).
• When you connect just one subwoofer, turn off “Subwoofer2.”
• After the setting, storing the setting contents on the unit is
recommended. For details, refer to “Storing the Preset Values (Preset
Store)” (page 12).
4-1
First time start-up:
Click [NEXT]. The AUX Input System Select screen will
display automatically. Continue to set, referring to
“Setting the AUX Input System (AUX Input System
Select)” (page 14).
4-2
Subsequent start-up:
Click [Close Window]. The confirmation screen will be
displayed. Click [OK]. Sound Manager for PXA-H800 will
be closed. Turn the ignition key to off and then on again.
The settings become effective.
Setting the Speakers (Speaker Setup)/
Setting the Subwoofers
Turn on the connected speakers.
If 2 subwoofers are connected, you can choose either stereo or monaural
for the subwoofer output. Set depending on the subwoofers to be
connected (Initial setting: “Mono”).
1
Click [Speaker Setup] for [Shortcut] tab in the main
menu.
The Speaker Setup screen is displayed.
• If you click [I/O Configuration] on the Function switching tab, and
then [Speaker Setup], the Speaker Setup screen will also be
displayed. Refer to “Operating the Function Switching Tab”
(page 7).
2
Click [Full Range], [ON] or [OFF], etc., to set the
speakers.
Front High*
1
: Full Range/Tweeter/OFF
Front Mid: Full Range
Front Low: Full Range/OFF
Rear: Full Range/OFF
Center: Full Range/OFF
Subwoofer (1, 2): ON/OFF
Subwoofer Output: Stereo/Mono *
2
*
1
When you modify the “Front High” speaker setting to [Full Range],
a message to confirm the change will be displayed. To set at “Full
Range,” select [YES] and click [OK]. Make sure the speaker being
used for this output is able to handle a full range source. Many
tweeters can be damaged when driven by a full range signal.
*
2
Only when two subwoofers are connected, is this item able to be set.
Stereo: Subwoofer stereo (L/R) output
Mono: Subwoofer monaural output
• Speakers that cannot be turned off do not show “OFF. ” Refer to
Table 1 (Output System) in “System Configuration” (page 60).
• When you connect just one subwoofer, turn off “Subwoofer2.”
• The speaker settings here will depend on which system was selected
in “Setting the Speaker System (Output System Select)” (page 13).
3
When setting is complete, click [Close Window].
• When the speaker setting is changed while ImprintEQ/RoadEQ is on,
ImprintEQ/RoadEQ will be turned off after a confirmation message
is displayed.
• After the setting, it is recommended to store the setting contents on
the unit. For details, refer to “Storing the Preset Values (Preset
Store)” (page 12).
Setting the AUX Input System (AUX Input
System Select)
This step sets the six channel RCA input of the unit. The input volume
levels can also be set.
At initial startup, the AUX Input System Select screen is displayed
automatically after the speakers are set. Step 1 is unnecessary.
1
Click [AUX Input System] for [Shortcut] tab in the
main menu.
The AUX Input System Select screen is displayed.
• When you click [I/O Configuration] on the Function switching tab,
and then [AUX Input System Select], the AUX Input System Select
screen will also be displayed. Refer to “Operating the Function
Switching Tab” (page 7).
2
Select and click the AUX Input System, and then
click [NEXT].
Analog 5.1ch. Input:
AUX1 (Front Left, Front Right, Rear Left, Rear Right,
Center, Subwoofer)
Analog 4ch. +2ch. Input:
AUX1 (Front Left, Front Right, Rear Left, Rear Right)/
AUX2 (Left, Right)
Analog 2ch. ×3 Input:
AUX1 (Left, Right)/AUX2 (Left, Right)/AUX3 (Left,
Right)
01GB00PXAH800.book Page 14 Tuesday, February 8, 2011 9:04 PM