Filter
Top Products
37-EN
01GB07PXAH800.fm
ALPINE PXA-H800_EN 68-13530Z65-A (B5)
From the Commander
5
Select one from “P.1” through “P.6” by rotating the
[Rotary encoder], and press the [Rotary encoder].
The data is stored in the selected preset number.
• The function is operable when Defeat is set to OFF.
• The stored contents are not deleted even when resetting the unit or
disconnecting the battery.
Recalling a Stored Setting (Preset Call)
The preset memory stores various setting/adjustment information. Thus,
it takes some time to call data from the preset memory.
1
Press and hold [VIEW] for at least 2 seconds.
2
Select a preset from “P.1” through “P.6” by rotating
the [Rotary encoder], and press the [Rotary
encoder].
The values of the selected preset number are retrieved.
• You can call the Preset even by the following procedure:
1 Press [FUNC.].
2 Rotate the [Rotary encoder] to select “Preset, ” and then
press the [Rotary encoder].
3 Rotate the [Rotary encoder] to select “Call,” and then
press the [Rotary encoder].
4 Select a preset from “P.1” through “P.6” by rotating the
[Rotary encoder], and press the [Rotary encoder].
The values of the selected preset number are retrieved.
• The function is operable when Defeat is set to OFF.
• If the speaker system in the preset and the current speaker system do
not match, the preset cannot be retrieved.
• If the AUX input system in the preset and the current AUX input
system do not match, the items concerning the AUX input system are
unavailable for retrieval.
Setting the Speaker System (System
Select)
First, set the system and the speakers. Unless you set the system, you
cannot set any features. Be sure to set the system first. If the selected
system and the connections of the speakers do not match, the speakers
may be damaged. Make sure to check the connections of the speakers
before selecting the system.
1
Press [FUNC.].
2
Rotate the [Rotary encoder] to select “Output
Setup,” and then press the [Rotary encoder].
3
Rotate the [Rotary encoder] to select “System
Select,” and then press the [Rotary encoder].
The Output System selection screen is displayed.
4
Rotate the [Rotary encoder] to select a system, and
then press the [Rotary encoder].
F-2way+R+SW: 4.2ch system
(Front2Way+Rear+Subwoofer)
F-3way+SW: 2.2ch system (Front3Way+Subwoofer)
F-3way+R: 4.0ch system (Front3Way+Rear)
F-2way+R+C+SW: 5.1ch system
(Front2Way+Rear+Center+Subwoofer)
• Refer to Table 1 (Output System) in “System Configuration”
(page 60).
5
Select “OK” by rotating the [Rotary encoder] when a
confirmation message appears, and press the
[Rotary encoder].
The Speaker Setup screen is displayed.
• When “OK” is selected, the audio output is stopped until the ignition
key is turned on/off.
6
Turn off any unconnected speakers. Rotate the
[Rotary encoder] to select “ON” or “OFF,” etc., and
then press the [Rotary encoder].
Repeat the steps until all the speakers are set.
FRONT HIGH*
1
: OFF/Tweeter/Full
FRONT LOW: OFF/ON
REAR: OFF/ON
CENTER: OFF/ON
SUBWOOFER(1, 2): OFF/ON
SW CHANNEL: Mono/Stereo*
2
Only for the initial startup:
1
Press the [FUNC.] or [Rotary encoder].
The Output System selection screen is displayed. Go to
Step 3.
01GB00PXAH800.book Page 37 Tuesday, February 8, 2011 9:04 PM