Filter
Top Products
43-EN
01GB07PXAH800.fm
ALPINE PXA-H800_EN 68-13530Z65-A (B5)
From the Commander
6
Rotate the [Rotary encoder] to select “Auto TCR,”
and then press the [Rotary encoder].
The AUTO TCR screen is displayed.
7
Press the [Rotary encoder].
Countdown will start.
During the 10 second countdown, go outside the vehicle
and close the door.
A test signal will be output from the speakers to measure the
acoustic characteristics of the cabin. Do not open any
doors until the screen indicates “Finished.” If external noise
interferes with the measurement, the “Calibration Error”
message will appear on the screen. In this case, click
[Rotary encoder] again to re-measure.
• If you want to stop measurement, press [ ].
• If the microphone is not connected, “No Mic” will be displayed and
the measurement will not be carried out. Press [ ] or [Rotary
Encoder] to cancel the indication.
8
When “Finished” appears, press [Rotary encoder].
• This function is not available when Defeat is set to ON.
• Measurement of Auto TCR takes approximately 5 minutes.
• Auto TCR measurement result overwrites the manual TCR
measurement result.
• Sound may arrive at the listening position at slightly different times,
depending on the speaker and enclosure. To compensate for this, the
distance can be adjusted to be larger than the actual distance.
• After the setting, it is recommended to store the setting contents on
the unit. For details, refer to “Storing the Preset Values (Preset
Store)” (page 36).
Adjusting for Road Noise (RoadEQ)
RoadEQ (REAL-TIME OPTIMIZED ADAPTIVE DRIVING EQ) is a
function to automatically adjust the EQ properties in accordance with
the road noise while driving.
The Road Equalizer compensates for constantly changing noise, so
always keep the microphones connected.
1
Preparing for measurement.
• Park the vehicle in a quiet location.
• Close doors, windows, sunroof, etc.
• Turn the air-conditioner and heater OFF.
• Turn off the engine of the vehicle.
2
Preparing the microphone.
Refer to the installation manual.
3
Turn the ignition switch of the vehicle to ACC (On).
• If an air-conditioner or heater is turned on, turn it off. Measurement
should not be performed if air-conditioner or heater noise is present.
4
Press [FUNC.].
5
Rotate the [Rotary encoder] to select “RoadEQ,” and
then press the [Rotary encoder].
6
Rotate the [Rotary encoder] to select “Calibration,”
and then press the [Rotary encoder].
The CALIBRATION screen is displayed.
7
Press the [Rotary encoder].
Countdown will start.
During the 10 second countdown, go outside the vehicle
and close the door.
A test signal will be output from the speakers to measure the
acoustic characteristics of the cabin. Do not open any
doors until the screen indicates “Finished.” If external noise
interferes with the measurement, the “Calibration Error”
message will appear on the screen. In this case, click
[Rotary encoder] again to re-measure.
• If you want to stop measurement, press [ ].
• If the microphone is not connected, “No Mic” will be displayed and
the measurement will not be carried out. Press [ ] or [Rotary
Encoder] to cancel the indication.
8
When “Finished” appears, press [Rotary encoder].
• This function is not available when Defeat is set to ON.
• Measurement of RoadEQ takes approximately 7 minutes.
• When you select “Calibration” again, the previous setup data will be
erased when count-down is started.
• Measurement values will not be lost in the event the system is reset or
battery power is disconnected.
When automatic measurement is completed, RoadEQ can be turned on
or off and its level can be selected.
1
Press [FUNC.].
2
Rotate the [Rotary encoder] to select “Road EQ,”
and then press the [Rotary encoder].
3
Rotate the [Rotary encoder] to select “Level
Adjustment,” and then press the [Rotary encoder].
The LEVEL ADJUSTMENT screen is displayed.
Turning RoadEQ On/Off
01GB00PXAH800.book Page 43 Tuesday, February 8, 2011 9:04 PM