Filter
Top Products
Advanced Settings
29
Setting Item Default Value Setting Details
Back 80Hz(THX) Select the crossover frequency from "40Hz" to
"200Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
"None": When no compatible speaker is connected
r
In the following cases, the setting will be set to
"None":
– "Surround" is set to "None".
r
"Full Band" can be selected only when
"Surround" is set to "Full Band".
Back Channel 2ch Select the number of channels of the connected
surround back speaker.
"1ch": When one speaker is connected (Connect to
the BACK L terminal)
"2ch": When two speakers are connected
r
The setting cannot be changed if "Back" is set to
"None".
Wide None Select the crossover frequency from "40Hz" to
"200Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
"None": When no compatible speaker is connected
r
In the following cases, this item will be set to
"None":
– "Surround" is set to "None".
– "Height 2 Speakers Type" is set to other than
"Not Use".
–
r
"Full Band" can be selected only when "Front" is
set to "Full Band".
Height 1 None Select the crossover frequency from "40Hz" to
"200Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
"None": When no compatible speaker is connected
r
If "Height 1 Speakers Type" is set to "Not Use",
this item will be set to "None".
r
"Full Band" can be selected only when "Front" is
set to "Full Band".
r
"None" cannot be selected when "Height 1
Speakers Type" is set to other than "Not Use".
Setting Item Default Value Setting Details
Height 2 None Select the crossover frequency from "40Hz" to
"200Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
"None": When no compatible speaker is connected
r
If "Height 2 Speakers Type" is set to "Not Use",
this item will be set to "None".
r
"Full Band" can be selected only when "Front" is
set to "Full Band".
r
"None" can be selected only when "Height 2
Speakers Type" is set to "Not Use".
LPF of LFE 120Hz Set the low-pass filter for LFE (low-frequency effect)
signals in order to pass lower frequency signals than
the set value and thus cancel unwanted noises. The
low-pass filter will be effective only on sources with
LFE channel.
Select a value between "80Hz" to "120Hz".
"Off": Do not use this function
Subwoofer Phase 0° Bass sound of the subwoofers may be insufficient
depending on the type of sound and the listening
position. In that case, change the phase of
subwoofers. Set the phase value while listening to
the sound so that you can obtain your preferred
bass sound.
"0°": The subwoofer is in normal phase.
"180°": The subwoofer is in reverse phase.
r
The setting cannot be changed if "Subwoofer" is
set to "No".
Double Bass ----- Boost bass output by feeding bass sounds from
the front left and right, and center speakers to the
subwoofer.
"On": Bass output will be boosted.
"Off(THX)": Bass output will not be boosted.
r
The setting will not automatically be configured even
if you performed the automatic speaker setup.
r
If "Subwoofer" is set to "No" or if "Front" is set to
other than "Full Band", the setting will be fixed to
"-----".
r
If you're using THX-certified speakers, we recommend the following settings:
– Set a value "80Hz(THX)" in Crossover frequency.
– Set a value "80Hz(THX)" in LPF of LFE.
– Set a value "Off(THX)" in Double Bass.