Filter
Top Products
NX-800/800H
60
ADJUSTMENT
Item
Condition Measurement Adjustment
Specifi cations /
Remarks
Panel test mode PC test mode
Test-
equipment
Unit
Terminal
Unit Parts Method
6. Low RSSI
at –118dBm
adjust *7
[Analog
Narrow]
1) Adj item:
[An LRSSI]
Adjust: [
✳✳✳
]
2) Adj item:
[AnL LRSSI]
→
[AnL’ LRSSI]
→
[AnC LRSSI]
→
[AnH’ LRSSI]
→
[AnH LRSSI]
SSG output:
–118dBm (0.28µV)
(MOD: 1kHz,
Dev: ±1.5kHz)
1) Adj item: [Low
RSSI (Narrow)]
2) Adj item: [Low],
[Low’], [Center],
[High’], [High]
SSG output:
–118dBm (0.28µV)
(MOD: 1kHz,
Dev: ±1.5kHz)
SSG ANT
Ext.SP
connec-
tor
[Panel test mode]
After input signal
from SSG, press
[ ]
key to store the
adjustment value.
[PC test mode]
After input signal
from SSG, press
[Apply] button to
store the adjust-
ment value.
[Analog
Wide]
1) Adj item:
[Aw LRSSI]
Adjust: [
✳✳✳
]
2) Adj item:
[AwL LRSSI]
→
[AwL’ LRSSI]
→
[AwC LRSSI]
→
[AwH’ LRSSI]
→
[AwH LRSSI]
SSG output:
–118dBm (0.28µV)
(MOD: 1kHz,
Dev: ±3kHz)
1) Adj item: [Low
RSSI (Wide)]
2) Adj item: [Low],
[Low’], [Center],
[High’], [High]
SSG output:
–118dBm (0.28µV)
(MOD: 1kHz,
Dev: ±3kHz)
[NXDN
Very
Narrow]
1) Adj item:
[Nv LRSSI]
Adjust: [
✳✳✳
]
2) Adj item:
[NvL LRSSI]
→
[NvL’ LRSSI]
→
[NvC LRSSI]
→
[NvH’ LRSSI]
→
[NvH LRSSI]
SSG output:
–118dBm (0.28µV)
(MOD: 1kHz,
Dev: ±1.5kHz)
1) Adj item: [Low
RSSI (Very Narrow)]
2) Adj item: [Low],
[Low’], [Center],
[High’], [High]
SSG output:
–118dBm (0.28µV)
(MOD: 1kHz,
Dev: ±1.5kHz)
Adjust with the ana-
log signal.
*7: Because “RSSI at –118dBm adjust” of NXDN Narrow is adjusted by adjusting “RSSI at –118dBm adjust [Analog Narrow]”, it is not necessary to
adjust “RSSI at –118dBm adjust” of NXDN Narrow.
7. High RSSI
at –80dBm
adjust *8
[Analog
Narrow]
1) Adj item:
[An HRSSI]
Adjust: [
✳✳✳
]
2) Adj item:
[AnL HRSSI]
→
[AnL’ HRSSI]
→
[AnC HRSSI]
→
[AnH’ HRSSI]
→
[AnH HRSSI]
SSG output:
–80dBm (22.4µV)
(MOD: 1kHz,
Dev: ±1.5kHz)
1) Adj item: [High
RSSI (Narrow)]
2) Adj item: [Low],
[Low’], [Center],
[High’], [High]
SSG output:
–80dBm (22.4µV)
(MOD: 1kHz,
Dev: ±1.5kHz)
SSG ANT
Ext.SP
connec-
tor
[Panel test mode]
After input signal
from SSG, press
[ ]
key to store the
adjustment value.
[PC test mode]
After input signal
from SSG, press
[Apply] button to
store the adjust-
ment value.