Alpine IVA-D310 Car Video System User Manual


 
33-EN
01GB05IVA310.fm
ALPINE IVA-D310 68-02278Z28-A (EN)
System Setup Operation
1
Touch [SETUP] on the main source screen.
The SETUP selection screen is displayed.
2
Touch [OTHER SETUP].
The OTHER SETUP screen appears.
3
Touch [] of SYSTEM SETUP.
The SYSTEM setup screen appears.
4
Touch [], [] or [OFF], [ON], etc., of the desired
item to change its setting.
Setting items:
IN INT. MUTE / IN INT. ICON / NAV. IN / NAV. MIX / VISUALIZER*
/ AUX IN-1 / AUX IN-2* / AUX IN-3* / MONITOR OUT-1 /
MONITOR OUT-2* / CAMERA IN / VISUAL KEY / A. PROC TYPE
/ OPTICAL OUT
* Displayed when the external expansion box VPE-S431 is
connected.
5
Touch [RETURN] to return to the previous screen.
Touch [CONTROL] to return to the main source screen that
was displayed before the setup operation was started.
Immediately after changing the settings of System Mode (While the
system is writing data automatically) do not turn the ignition key
(engine key) to OFF.
Otherwise, the settings may not be changed.
If an Alpine Ai-NET Auxiliary Input Adapter (KCA-801B) is
connected to the IVA-D310, an Auxiliary Source will be allowed to
interrupt the current audio source. For example, you can listen to a
portable MP3 player through your car audio system even with a CD
changer connected and playing. The CD changer will automatically
mute when switched to the AUX Input. For further details on how to use
the Alpine KCA-801B, see your authorized Alpine dealer.
Setting item: IN INT. MUTE
Setting content: OFF / ON
The auxiliary device being connected must have an Interrupt wire
with a negative trigger for this function to operate automatically.
Otherwise, a separate switch needs to be added to switch it manually.
The unit can display the icon of an external device, such as a telephone,
whenever a phone call comes in to tell you there is a phone call.
Setting item: IN INT. ICON
Setting content: INT / TEL
When you connect an optional navigation equipment, set it to ON.
Setting item: NAV. IN
Setting contents: OFF / ON
With an Alpine navigation system connected to the IVA-D310, the voice
guidance of the navigation system will be mixed with the radio or CD
play.
Setting item: NAV.MIX
Setting content: OFF / ON
To adjust the navigation interruption volume level, the adjustment
for NAV. LEVEL can be performed in “Adjusting the Audio” on
page 23 after setting to ON.
The audio volume during the navigation guide can be set by
adjusting the audio volume while the navigation guide continues.
When the navigation guide finishes, the previous audio volume and
the previous screen are restored. For exception, if the navigation cuts
in when the audio volume is lower than the setting level, the audio
volume during the navigation guide is reset the current listening
volume. (When the navigation guide cuts in, the audio volume does
not increase.)
This setting is effective when NAV.IN of SYSTEM list screen is ON.
When PXA-H510 or PXA-H900 is connected, NAV.MIX value set in
this unit does not affect PXA-H510 or PXA-H900.
SYSTEM Setup
To display the System mode screen:
To watch a video source, your vehicle must be parked with the
ignition key in the ACC or ON position. To do this, follow the
procedure below.
1 Brake to bring your vehicle to a complete stop at a
safe location. Engage the parking brake.
2 Keep pushing the foot brake and release the parking
brake once then engage it again.
3 When the parking brake is engaged for the second
time, release the foot brake.
For automatic transmission vehicles, place the transmission lever
in the Park position.
Now, the locking system for the System mode operation has been
released. Engaging the parking brake can reactivate the System
mode, as long as the car's ignition has not been turned off. It is
not necessary to repeat the above procedure (1 through 3), of
“To display the System mode screen.”
Each time the ignition is turned OFF, perform the procedure of “To
display the System mode screen.”
The following steps 1 to 5 are common operations to each
“Setting item” of SYSTEM Setup. Refer to each section for
details.
Setting the External Device Interrupt Mode
OFF: The volume level can be adjusted in Interrupt mode.
ON: Sound will not be output. The icon that is set in “Setting
the Interrupt Icon Display” is displayed.
Setting the Interrupt Icon Display
INT: The INT icon appears on the display.
TEL: When the external device (telephone) sends the interrupt
signal, the telephone icon appears on the display.
Setting the Navigation Mode
ON: Navigation source is displayed.
OFF: Navigation source is not displayed. The settings related
to the navigation can not be changed from this unit.
Setting the Navigation Interruption
OFF: The navigation interruption mode is turned off.
ON: The navigation interruption mode is on.
01GB00IVAD310.book Page 33 Wednesday, December 1, 2004 4:20 AM