Filter
Top Products
143
Speakers
Setting items Setting details
Distances
Set distance from listening
position to speakers.
Measure beforehand the
distance from the listening
position to each speaker.
Unit : Set the unit of distance.
•Feet / Meters
Step : Set the minimum variable width of the distance.
•1ft / 0.1ft
•0.1m / 0.01m
Set Defaults : The “Distances” settings are returned to the default
settings.
•Reset : Reset to the defaults.
•Cancel : Do not reset to the defaults.
When you select “Set Defaults” and press
ENTER, the “Resets all of the distance
settings to the factory defaults?” prompt is
displayed. Select either “Reset” or “Cancel”,
and press ENTER.
Front L / Front R / F. Height L / F. Height R / F. Wide L / F. Wide R /
Center / Subwoofer 1
z1
/ Subwoofer 2
z1
/ Surround L / Surround R /
Surr.Back L
z2
/ Surr.Back R
z2
: Select speaker for distance setting.
z1 When the “Speaker Config.” – “Subwoofer” setting (vpage142)
is set to “1spkr”, “Subwoofer” is displayed.
z2 When the “Speaker Config.” – “Surr.Back” setting (vpage142)
is set to “1spkr”, “Surr.Back” is displayed.
•0.0ft – 60.0ft / 0.00m – 18.00m : Set the distance.
•The speakers that can be selected differ depending on the “Amp Assign”
(vpage141) and “Speaker Config.” (vpage142) settings.
•Default settings :
Front L / Front R / F. Height L / F. Height R / Front Wide L / Front Wide R /
Center / Subwoofer 1 / Subwoofer 2 : 12.0 ft (3.60 m)
Surround L / Surround R / Surr.Back L / Surr.Back R : 10.0 ft (3.00 m)
•Set the difference in the distance between the speakers to less than
20.0 ft (6.00 m).
NOTE
Speakers set to “None” in “Speaker Config.” (vpage 142) are not
displayed.
Setting items Setting details
Levels
Set the volume of the test
tone to be the same when it
is output from each speaker.
Test Tone Start : Output test tone.
•Front L / F. Height L / Center / F. Height R / Front R / F. Wide R /
Surround R / Surr. Back R
z1
/ Surr. Back L
z1
/ Surround L /
F. Wide L / Subwoofer 1
z2
/ Subwoofer 2
z2
/ Subwoofer 1+2
z3
:
A test tone is output from the selected speaker. While listening to the
test tone, adjust the volume output from the selected speaker.
z1 When the “Speaker Config.” – “Surr.Back” setting (vpage142)
is set to “1spkr”, “Surr.Back” is displayed.
z2 When the “Speaker Config.” – “Subwoofer” setting (vpage142)
is set to “1spkr”, “Subwoofer” is displayed.
z3 When “Subwoofer 1+2” is selected, you can adjust the volume of
Subwoofer 1 and Subwoofer 2 at the same time.
•–12.0dB – +12.0dB (0.0dB) : Adjust the volume.
When “Levels” is adjusted, the adjusted values are set for all the
sound modes.
NOTE
•Speakers set to “None” in the “Speaker Config.” (vpage 142)
settings are not displayed.
•When a headphones jack is inserted in the PHONES jack of this unit, the
“Levels” is not displayed.
Set Defaults : The “Levels” settings are returned to the default settings.
•Reset : Reset to the defaults.
•Cancel : Do not reset to the defaults.
When you select “Set Defaults” and press
ENTER, the “Reset all of the channel level
settings to the factory defaults?” prompt is
displayed. Select either “Reset” or “Cancel”,
and press ENTER.
Basic version
Advanced version
Informations
Advanced version
v See overleaf
DVD