Filter
Top Products
145
Speakers
Setting items Setting details
Impedance
Set the impedance of
connected speakers.
8Ω/ohms : Select when the impedance per speaker for all the connected
speakers is 8Ω or larger.
6Ω/ohms : Select when the impedance for any of the connected speakers
is between 6Ω and 8Ω.
4Ω/ohms : Select when the impedance for any of the connected speakers
is between 4Ω and 8Ω.
Check the speaker impedance (Ω) shown on the back of your speakers
or in the instruction manual beforehand.
Front Speaker
Set the front speakers to
use for every sound mode.
2ch Playback : The front speakers used in direct play (2 channel), stereo
play and pure direct play (2 channel) are set in advance.
•A : Front speaker A is used.
•B : Front speaker B is used.
•A+B : Both front speakers A and B are used.
Multi ch Playback : The front speakers used in play modes other than
direct play (2 channel), stereo play and pure direct play (2 channel) are set
in advance.
•A : Front speaker A is used.
•B : Front speaker B is used.
•A+B : Both front speakers A and B are used.
This can be set when “Assign Mode” (vpage141) is set to “7.1ch
+ Front B”.
2ch Playback
Select the method for
setting the speakers used
in the 2-channel direct and
stereo playback modes.
Setting : Select the method for setting the speakers used in the 2-channel
direct and stereo playback modes.
•Auto : The settings at “Speakers” (vpage139) are applied.
•Manual : Make separate settings for 2-channel. Make the following
settings:
Front : Set the front speaker size.
•Large : Use a large speaker that can adequately play back low
frequencies.
•Small : Use a small speaker that has inadequate playback capacity for
low frequencies.
If “Speaker Config.” – “Subwoofer” (vpage142) is set to “None”,
the setting is automatically set to “Large”.
Setting items Setting details
2ch Playback
(Continued)
Subwoofer : Set the presence of a subwoofer.
•Yes : Use a subwoofer.
•No : Select when a subwoofer is not connected.
If “Speaker Config.” – “Subwoofer” (vpage142) is set to “None”,
the setting is automatically set to “No”. If the “Front” setting is
“Small”, the setting is automatically “Yes”.
SW Mode : Select low range signals to be reproduced by subwoofer.
•LFE : When the “2ch Playback – “Front” setting is set to “Large”, the
LFE signal alone is output from the subwoofer. Also, when the “2ch
Playback” – “Front” setting is set to “Small”, the front channel low
range signal is added to the LFE signal output from the subwoofer.
•LFE+Main : The front channel low range signal is added to the LFE signal
output from the subwoofer.
This setting can be set made “2ch Playback” – “Subwoofer” is set to
“Yes”.
Crossover : Set the maximum frequency of the bass signal output from
each channel to the subwoofer.
•40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz
•This setting can be set made “2ch Playback” – “Subwoofer” is set to
“Yes”.
•If the “2ch Playback” – “Front” setting is “Large” and the “SW Mode”
setting is “LFE”, “Full Band” is displayed and the setting cannot be
made.
Distance FL / Distance FR : Select speaker for distance setting.
•0.0ft – 60.0ft (12.0ft) / 0.00m – 18.00m (3.60m) : Set distance from
main listening point to speaker.
Set the difference in the distance between the speakers to less than
20.0 ft (6.00 m).
Level FL / Level FR : Select speaker for level adjustment.
•–12dB – +12dB (0dB) : Adjust the level of each channel.
Basic version
Advanced version
Informations
Advanced version
DVD