Filter
Top Products
Advanced Operations
En-85
Adjusting the Volume for Zones
■ Operating on the remote controller
■ Operating on the AV receiver
If your Zone 2/3 speakers are connected to a receiver
or integrated amplifier in Zone 2/3, use its volume
control to adjust the volume.
Muting Zones
■ Operating on the remote controller
Tip
• To unmute, press ZONE followed by MUTING again. Zones
can also be unmuted by adjusting the volume.
Note
• ZONE 2 LINE OUT and ZONE 2 L/R output 2ch PCM,
analog, NET or USB input sources. To listen to the PCM
source, you need to make an HDMI connection.
• Only analog, NET or USB input source is output from the
ZONE 3 LINE OUT jacks and ZONE 3 L/R terminals.
• You cannot select different AM or FM radio stations for your
main room and Zone 2/3. The same AM/FM radio station
will be heard in each room. Namely, if you have selected an
FM station for the main room, that station will also be output
in Zone 2/3.
• If an HDMI component selected in Zone 2 outputs the
sound other than PCM, the sound is not output from
ZONE 2 L/R and ZONE 2 LINE OUT.
• Both audio and video outputs from an HDMI component
may interrupt when the main room and Zone 2 are set to
share the same source or not.
• You cannot select different input selector NET or USB for
your main room and Zone 2/3. Namely, if you have selected
USB input selector for Zone 2/3, USB input selector will be
selected in main room even if NET has been selected for
main room.
•“BLUETOOTH” cannot be selected as input selector in
Multi Zone. If you play audio from Bluetooth-enabled device
in Multi Zone, select “Zone 2 Selector: Source” or “Zone 3
Selector: Source”, and “BLUETOOTH” as input selector in
Main room.
• When Zone 2/3 is activated and its input selector is
selected, the power consumption of standby mode slightly
increases.
• While Zone 2/3 is on, functions will not work.
• The component connected to HDMI input other than HDMI
IN 1/2/3/AUX INPUT is selected as an input source for
Zone 2, the linked operations of may not work
properly. In this case, set the linked operations to Off on the
source component.
• When setting the AV receiver to standby mode while Zone
2/3 is active, the Z2 or Z3 indicator is dimly lit.
• Activating Zones in the main room when the listening mode
is set to Pure Audio will automatically switch it to Direct.
•“GAME2” cannot be selected as input sources for Zone 3.
• When “GAME2” is the input source of Main room and
Zone 3 is set to share the same source, no sound will be
output from Zone 3.
• Even if you repeatedly press the remote controller’s ZONE
to select zones, the last zone selection will be retained once
you have switched to other components by pressing other
REMOTE MODE after pressing ZONE.
1
Press ZONE repeatedly, then point the remote
controller at the AV receiver and press
RECEIVER.
Zone 2/3 turns on, the Z2 or Z3 indicator lights on
the AV receiver’s display.
Tip
• The corresponding trigger output goes high (+12 V).
2
To select an input source for Zone 2/3, press
ZONE repeatedly, followed by an INPUT
SELECTOR button.
To select AM or FM, press ZONE and the TUNER
input selector repeatedly.
3
To turn off Zone 2/3, press ZONE repeatedly,
followed by RECEIVER.
The zone is turned off.
Tip
• The corresponding trigger output goes low (0 volts).
1
Press ZONE repeatedly.
2
Use VOL / .
1
Press ZONE 2 or ZONE 3 (the Z2/Z3 indicator
on the AV receiver’s display flashes).
2
Use MASTER VOLUME control within 8
seconds.
1
Press ZONE repeatedly, and then press
MUTING.